Occidental Leather Framing Tool Belts & Carpenter Bags

Occidental Leather 5006 Features

• Thick-pile sheepskin lining for maximum comfort
• Heavy harness leather exterior for durability
• No leading edge to prevent pressure points
• Slots accept belts up to 3 in wide
• Requires 1 to 2 in extra belt length
• Lighter than full belt liner model 5005
• Handmade in USA

Occidental Leather 5006 Applications

• Increase comfort when wearing loaded tool belts
• Reduce hip pressure during carpentry and framing work
• Use under tool bags to cushion heavy setups
• Improve circulation on long wear days

Occidental Leather 5006 Installation Overview

1. Loosen or remove tool bags from the work belt.
2. Slide each hip pad onto the belt using the end slots and position at the hips.
3. Reattach tool bags over the pads as needed.
4. Adjust belt length to account for 1 to 2 in extra length.
5. Check fit and comfort before use.

Occidental Leather 5355 Key Features

• Suspension system redistributes belt load for reduced strain
• Hip Buddies padding softens impact on hips and lower back
• Accepts any bag up to 7.5 inches wide
• Made in USA; leather and nylon construction
• Available colors: OxyRed and Black
• Not compatible with Adjust-to-Fit systems or Stronghold Comfort Belts; does not fit 5525 or B5611 bags

Occidental Leather 5355 Applications

• Comfort upgrade for heavy tool belt setups
• Reducing hip and lower back fatigue on long shifts
• General construction, carpentry, electrical, and remodeling work
• Supporting weight evenly during climbing, bending, and overhead tasks

Occidental Leather 5355 Installation Overview

1. Attach the 9008 Hip Buddies around your work belt at the hip areas.
2. Clip the 5055 suspension straps to the belt D-rings or belt loops per your setup.
3. Adjust front and rear strap lengths for even weight distribution.
4. Secure the chest strap for stability and fine tune fit.
5. Verify bag width does not exceed 7.5 inches and confirm compatibility.

Occidental Leather 5595 Key Features

• Go beltless using bags that accept a 3 inch belt
• Enables use of traditional Occidental bags
• Made in USA
• Does not accommodate 5611 or B5611

Occidental Leather 5595 Applications

• Upgrade existing tool bags to a beltless carry system
• Improve comfort for extended wear on the jobsite
• Customize tool bag setups without a waist belt

Occidental Leather 5595 Installation Overview

1. Verify your bags accept a 3 inch belt.
2. Attach kit hangers to compatible bags.
3. Connect the harness and clips per layout.
4. Adjust straps for fit and balance.
5. Confirm secure attachment before loading tools.

Occidental Leather 8062 Features

• 4 pouch layout with main, middle, outer, and upper bags
• 10 total pockets and tool holders
• Dedicated holders for blade square, angle square, cat's paw, and driver bits
• Streamlined profile for compact, efficient storage
• Designed to be worn on the left side for right handed users; left handed option available
• Made in USA

Occidental Leather 8062 Applications

• Framing tasks requiring quick access to fasteners and layout tools
• General carpentry where compact, organized storage is preferred
• Keeping squares, bits, and cat's paw readily accessible on the non dominant side

Occidental Leather 8585XL Key Features

• Hand specific tool holders for efficient layout
• Padded two ply tool bags hold their shape
• Industrial nylon is highly abrasion resistant
• Leather tool holders with leather reinforced corners
• Available left handed as model 8585LH

Occidental Leather 8585XL Applications

• Carpentry and framing setups
• General construction tool carry
• Remodeling and jobsite installation work

Occidental Leather 8585XL Installation Overview

1. Lay your current belt flat; measure from buckle end to most used hole.
2. Select the Extra Large size closest to that mid range measurement.
3. Position bags and holders to preferred left or right layout.
4. Secure buckle and adjust for a snug, supportive fit.

Occidental Leather 5061 Key Features

• All leather construction built for daily jobsite durability
• Top tape pocket for quick access
• Nine total pockets and holders for fasteners and layout tools
• Two lower bags to sort small tools and nails
• Tool slots for angle square, cat's paw, driver bits, and more
• Available in right- or left-hand setups
• Made in the USA

Occidental Leather 5061 Applications

• Framing and general carpentry layouts
• Finish work where organized fastener access is needed
• Jobsite fastener and small tool organization on a tool belt

Occidental Leather 5061 Specifications

Occidental Leather 5017DB Key Features

• Most popular layout without a tape pocket
• Double outer bags for added organization
• Holders for hammer, pencils, knife, crayon, chisel, torpedo level
• Right side wear for tools accessed with the right hand
• Available in left hand version as 5017DBLH
• Made in USA

Occidental Leather 5017DB Applications

• Organizing core hand tools on the jobsite
• Framing and general carpentry work
• Remodeling and installation tasks
• Trim and finish carpentry tool carry
• Daily use on professional work belts

Occidental Leather 5017DB Installation Overview

1. Slide the bag onto a work belt up to 3 inches wide.
2. Position on the right side for right hand access.
3. Load tools into main and outer pockets and holders.
4. Adjust placement for balance and comfort.
5. Securely fasten belt and verify easy access to tools.

Occidental Leather 5066 Features

• Premium full grain leather construction for long term durability
• Angled ergonomic design for improved balance and access
• Two built in holders for drill or driver bits
• Fits most cordless drills
• Available in right or left handed versions; left handed model 5066LH
• Made in the USA

Occidental Leather 5066 Applications

• Hands free carry of cordless drills on the jobsite
• Quick access drilling for framing and carpentry
• Tool organization for electricians and installers
• General construction and remodeling tasks

Occidental Leather 5066 Installation Overview

1. Slide holster onto your work belt at the preferred position.
2. Adjust placement for comfortable angled access.
3. Secure the retention strap snap if desired.
4. Insert drill fully; place bits in the dedicated holders.
5. Test movement to ensure secure, unobstructed access.

Occidental Leather B5080DB LG Features

• 22 pockets and tool holders
• Premium top grain leather construction
• Hand Specific tool holder placement for efficient workflow
• Copper rivets reinforce main bags
• NoSpill tool holder system
• Function engineered for modern builders

Key Features

• Hand-specific tool holders for efficient access
• Padded two-ply, foam-core bags maintain shape
• Abrasion-resistant industrial nylon construction
• Adjust-to-Fit belt allows quick sizing changes
• D-rings pre-installed for suspension system compatibility
• Left-handed model available as 9540LH
• Made in USA

Applications

• Finish carpentry setups
• Trim installation
• Light framing tasks
• General jobsite tool and fastener organization

Installation Overview

1. Adjust belt to fit over typical work clothing.
2. Position left fastener and right tool bags for reach preference.
3. Attach the high mount hammer holder at the center back.
4. Clip Oxy Tool Shields to bags or belt as needed.
5. Load tools and fasteners evenly; connect suspenders to D-rings if used.

Occidental Leather 5018 Key Features

• Right-hand layout with holders for pencils, utility knife, lumber crayon, chisel, torpedo level, and hammer
• Integrated tape measure holster fits tapes up to 35 ft
• Durable full-grain leather construction
• Two main pouches for fast access and organization
• Available in a left-hand version (5018DBLH / 5018LH)

Occidental Leather 5018 Applications

• Carpentry and framing tool carry
• Finish work and trim installation
• General construction and remodeling
• Measuring, marking, and layout tasks
• Jobsite tool organization on a work belt

Occidental Leather 5018 Installation Overview

1. Thread the bag onto a compatible work belt.
2. Position on the right side for right-hand access.
3. Load tools into designated holders and pouches.
4. Place tape in the built-in holster.
5. Verify balance and adjust placement for comfort.

Occidental Leather 5328 Key Features

• Made in the USA
• 10 oz Latigo belting leather construction
• Heavy-duty spring steel belt clip
• Italian-style drop clasp
• Clips to belts up to 2 inches wide
• Sized for larger smartphones (iPhone Plus and similar)

Occidental Leather 5328 Applications

• Keep smartphones secure and accessible on the jobsite
• Belt-mounted carry for larger phones
• Protection from bumps, dust, and debris
• Everyday use for trades and field work

Occidental Leather 5328 Installation Overview

1. Attach the holster by clipping it to a belt up to 2 inches wide.
2. Place the phone inside the holster.
3. Close the drop clasp to secure the phone.
4. Check that the clip is fully engaged before use.

Occidental Leather 5089 XXL Features

• Premium top grain leather construction
• Hand-specific tool holders for efficient workflow
• Copper rivet reinforcements on main bags
• NoSpill tool holder system for secure storage
• Function engineered for professional framers
• Available left-handed option: 5089LH
• Made in the USA

Occidental Leather 5089 XXL Applications

• Framing: organize and carry essential tools and fasteners
• General carpentry: keep hand tools accessible on site
• Jobsite setup: maximize capacity with seven pouch layout
• Heavy outdoor use: durable leather for demanding conditions

Occidental Leather 5089 XXL Installation Overview

1. Measure from the end of your belt buckle to the hole you use to fasten.
2. Select the belt size closest to that measurement; XXL is mid range 49 inches.
3. Attach tool and fastener bags to the belt per your hand preference.
4. Secure the hammer holder and adjust belt to the midpoint hole.
5. Load tools and confirm comfortable, balanced fit.

Occidental Leather 5525 Key Features

• Round-bottom design increases internal volume and stability
• 10 pockets and holders optimized for fasteners and layout tools
• Tape pocket fits tapes up to 35 ft
• Includes Oxy Tool Shield to protect sharp tools, bags, and body
• Right-hand layout; worn on the left side
• Premium leather construction; Made in the USA

Occidental Leather 5525 Applications

• Fastener storage for framing and carpentry tasks
• Organizing layout tools like squares and bits
• Measuring and marking with quick tape access
• Daily jobsite carry on a work belt

Occidental Leather 5525 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the left side for right-handed use.
3. Insert the Oxy Tool Shield into the designated holder.
4. Load fasteners and tools into the appropriate pockets.
5. Confirm secure fit and balance before use.

Occidental Leather 8060 Features

• 3-pouch layout for fasteners and small tools
• Tool-specific holders for blade square, angle square, cat's paw, and bits
• Lightweight OxyLights construction with leather reinforcements
• Optimized for framing and general carpentry
• Made in USA

Occidental Leather 8060 Applications

• Framing: Keep nails, layout square, and bits at hand
• General Carpentry: Organized storage for everyday fasteners
• Layout Work: Dedicated blade square and angle square holders
• Punch list tasks: Compact carry of small tools and hardware

Occidental Leather 8060 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the left side for right-handed setups or per preference.
3. Load fasteners and layout tools into the main, outer, and upper pouches.
4. Use dedicated holders for blade square, angle square, bits, and cat's paw.
5. Check balance and retention before starting work.

Occidental Leather 5019 Features

• All-leather construction for durability
• Clean interior with no tool holders or dividers
• Compact size suited for fasteners and small tools
• Made in USA
• Riveted and stitched for strength

Occidental Leather 5019 Applications

• Carry loose fasteners on the job
• Store small hand tools or accessories
• Add-on third bag for tool belt systems
• General utility storage for carpentry or trade work

Occidental Leather 5019 Installation Overview

1. Slide pouch onto compatible work belt or mount per your rig setup.
2. Position for comfortable reach and balance.
3. Load with fasteners or small tools; avoid overfilling.
4. Check stitching and rivets periodically for wear.

Occidental Leather 6104 Key Features

• Streamlined 2-pouch utility design
• No tool holders inside or outside for simple storage
• Durable leather construction
• Lightweight and compact for belt setups
• Made in the USA

Occidental Leather 6104 Applications

• Storing fasteners and small hardware
• Carrying loose hand tools
• Expanding capacity on a tool belt
• Organizing overflow items on the jobsite

Occidental Leather 6104 Installation Overview

1. Thread the bag onto a compatible work belt.
2. Position for preferred access on your belt setup.
3. Load fasteners or small tools into main and outer pouches.
4. Check balance and adjust placement as needed.

Key Features

• 21 pockets and tool holders
• Hand specific tool holder layout
• Padded two ply tool bags keep their shape
• Extremely abrasion resistant industrial nylon with leather reinforcement
• Made in USA

Applications

• Framing and rough carpentry
• General construction and remodeling
• Jobsite fastener and hand tool organization
• Production carpentry requiring high capacity storage

Installation Overview

1. Select size Large; mid range fit is 41 in. with 4 in. adjustment each way.
2. Thread the pouches onto the 3 in. Ranger belt and position for dominant hand.
3. Secure the High Mount Hammer Holder at the rear center.
4. Load tools and fasteners; balance weight across both bags.
5. Buckle belt using one of 9 holes; ensure snug, comfortable fit.

Occidental Leather 9504 Key Features

• Cost efficient organization for small tools and fasteners
• Seven-pocket, multi-pouch design with holders for pencil, utility knife, and angle square
• Heavy-duty clip attaches quickly to belts or waistbands
• Fits belts up to 2 inches wide
• Made in USA

Occidental Leather 9504 Applications

• Small repairs and punch list tasks
• Trim and finish work
• General maintenance rounds
• Weekend DIY projects

Occidental Leather 9504 Installation Overview

1. Load tools and fasteners into main and outer pockets.
2. Clip the pouch to your belt or waistband.
3. Ensure clip is fully engaged; adjust placement for comfort.

Occidental Leather 9008 Key Features

• High density cushion technology for hip comfort
• Light weight pads retrofit quickly to existing belt sets
• Accepts any bag up to 7.5 in wide
• Does not accommodate the 5525 Big Oxy Fastener Bag or B5611 Green Building Fastener Bag
• Made in the USA

Occidental Leather 9008 Applications

• Increase hip comfort on heavy tool belt setups
• Retrofit comfort upgrade for existing Occidental or other belt worn systems
• Use with compatible tool bags up to 7.5 in wide

Occidental Leather 9008 Installation Overview

1. Remove tool bags from your belt.
2. Slide a Hip Buddy onto each side of the belt at the hip locations.
3. Reinstall tool bags ensuring each is 7.5 in wide or less.
4. Adjust position for comfort and secure all attachments.

Occidental Leather 5526 Key Features

• Round-bottom leather construction adds volume and resists collapse
• Tool-specific storage: torpedo level slot, bit holders, pencil and chisel pockets
• Right-hand layout; worn on the right side
• Includes Oxy Tool Shield for safe carry of sharp tools
• Not available in a left-hand model

Occidental Leather 5526 Applications

• Carpentry and framing tool organization on a work belt
• Right-hand access to frequently used tools
• Jobsite fastener and small tool storage
• General construction and remodeling tasks

Occidental Leather 5526 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the right side for dominant-hand access.
3. Insert the Oxy Tool Shield into the designated pocket.
4. Load tools into dedicated holders and pockets.
5. Check balance and security before working.

Occidental Leather 2580 Key Features

• Maximum comfort with wide padded shoulder yoke lined with Dri-Lex for moisture control
• Even load distribution reduces back fatigue and increases carry efficiency
• Fully adjustable straps; one size fits most
• Quick release chest buckle for fast on/off
• Heavy-duty storage D-ring for hanging
• 36 pockets and tool holders for organized access
• Made in USA

Occidental Leather 2580 Applications

• Framing tasks requiring balanced tool carry
• Electrical installations and service work
• Concrete forming and layout
• Trim carpentry and finish work

Occidental Leather 2580 Installation Overview

1. Adjust shoulder straps and side straps for a comfortable fit.
2. Attach included tool and fastener bags to the leather belting.
3. Secure the chest buckle; verify even weight distribution.
4. Load essential tools into pockets and holders.
5. Use the D-ring to hang the vest when storing off the clock.

Occidental Leather 5564 Key Features

• All leather main bag with divided nylon double outer pouch
• Six black leather tool holders; four pouches total
• Optimized for wire nuts, couplers, and small fasteners
• Left side wear for fast access with the left hand
• Full grain leather and industrial nylon construction

Occidental Leather 5564 Applications

• Organizing and carrying fasteners and small parts
• Keeping layout and marking tools at hand
• Electrical and mechanical fittings storage
• Daily jobsite use with hybrid leather and nylon durability

Occidental Leather 5564 Installation Overview

1. Slide the belt loop over your work belt.
2. Position on the left side for non dominant hand access.
3. Distribute tools and fasteners among the divided pouches.
4. Secure frequently used layout tools in the leather holders.

Occidental Leather 9550 Key Features

• Premium top-grain leather bags with copper-riveted stress points
• Adjust-to-Fit belt for pant waist 32 to 41; locks securely in place
• Rugged commercial nylon belt with high-density neoprene padding
• D rings pre-installed for use with suspension systems
• Hand-specific tool holders for efficient workflow
• Fixed-position bags help prevent shifting
• Made in USA

Occidental Leather 9550 Applications

• Framing and rough carpentry
• General residential and commercial construction
• Remodeling and jobsite service work
• Tool and fastener organization on the go
• Use with suspension systems for extended wear

Occidental Leather 9550 Installation Overview

1. Adjust belt to your pant waist size (32 to 41) and secure the crossover system.
2. Position the tool bag on your dominant side and fastener bag opposite.
3. Attach the removable High Mount Hammer Holder on the rear as desired.
4. Clip suspension system to pre-installed D rings if used.
5. Load tools and fasteners; confirm bags sit securely without shifting.