Tool Belt Systems

Key Features

• Premium top-grain leather with hand-set copper rivets
• NoSpill tool holder system for secure organization
• Hand-specific layout promotes an efficient working rhythm
• Function engineered for framing professionals
• Available in left-hand (5089LH) and right-hand setups

Applications

• Framing and rough carpentry
• Residential production work
• Daily jobsite tool & fastener organization
• General carpentry and remodeling

Installation Overview

1. Measure your current tool belt from buckle end to the most-used hole.
2. Select the size whose midpoint matches your measurement.
3. No belt to measure? Add about 4″ to your pant waist for an approximate midpoint.
4. Adjust so the buckle closes near the midpoint hole for best fit.

Key Features

• Hand-specific tool holders for efficient workflow
• Padded two-ply bags maintain shape when empty or loaded
• Industrial nylon exterior with leather holders and reinforced corners
• FatLip leather mouth keeps bags open and resists wear
• Full leather boot for rugged longevity
• 3" HD ranger belt with center 2?in?1 tool & hammer holder
• Pockets & tool holders: 25
• Made in the USA

Applications

• Framing and production carpentry
• General construction and remodeling
• Jobsite tool and fastener organization
• Left- or right-hand optimized setups for daily use

Installation Overview

1. Measure an existing tool belt from buckle end to your most-used hole to determine size.
2. Select the belt size closest to that midpoint measurement.
3. Position tool bag on dominant hand side and fastener bag opposite.
4. Secure the belt at the midpoint hole; adjust for comfort and balance.
5. Load tools and fasteners by task to optimize workflow.

Occidental Leather 8003 Key Features

• 3" wide padded nylon belt body for balanced load support
• 2" heavy-duty leather tongue with nickel-plated steel roller buckle
• Lightweight industrial nylon reduces fatigue
• Works with most tool and fastener bags; suspenders compatible
• Made in USA

Occidental Leather 8003 Applications

• Foundation belt for tool and fastener bag setups
• Daily jobsite wear requiring comfort and support
• Use with suspenders for heavier rigs

Occidental Leather 8003 Installation Overview

1. Measure your current tool belt from buckle end to the hole you use most.
2. Select the size closest to that midpoint measurement.
3. Attach your tool/fastener bags and suspenders as needed.
4. Adjust to the midpoint hole; fine-tune within the 4" range.

Occidental Leather 9850 Features

• FatLip leather-reinforced bag mouth stays open and resists abrasion
• 10" deep main bags with full leather boot for rugged wear
• High-density neoprene, rugged nylon, and full-grain leather construction
• Adjust-to-Fit belt for 32"–41" waist sizes
• Rear 2-in-1 tool & hammer holder
• Oxy Tool Shield for sharp tool protection
• D-rings pre-installed for use with suspenders
• 24 pockets and tool holders
• Made in the USA

Occidental Leather 9850 Applications

• Production carpentry and framing
• General construction tool carry and organization
• Remodeling tasks requiring fast access to tools and fasteners
• Jobsite setup where balanced, comfortable load carry is needed

Occidental Leather 9850 Installation Overview

1. Adjust the belt using the Adjust-to-Fit system to your size (32"–41").
2. Place the tool bag on your dominant side and the fastener bag opposite.
3. Attach the 2-in-1 holder and Oxy Tool Shield to the rear center loops.
4. Load tools and fasteners into designated pockets for balance.
5. Secure straps, test mobility, and connect suspenders to D-rings if desired.

Key Features

• Hand-specific tool holder layout for efficient workflow
• Padded two-ply bags maintain shape
• Abrasion-resistant industrial nylon with OxyRed leather reinforcements
• NoSpill leather tool holders for secure access
• Made in the USA

Applications

• Framing and general carpentry
• Jobsite tool and fastener organization
• Rough construction and remodeling
• Left- or right-handed setups for professional builders

Installation Overview

1. Measure your current tool belt from buckle end to the hole you use most.
2. Match that measurement to the size chart midpoint (SM–XXXL).
3. Assemble belt, tool bag, fastener bag, and hammer holder per your handedness.
4. Adjust to the midpoint hole for best fit, with about 4" of adjustment each way.
5. Load tools and fasteners; verify balance and accessibility.

Occidental Leather 5080DB Features

• Premium top?grain leather for tough, outdoor jobsite use
• Hand?specific tool layout to promote natural working rhythm
• NoSpill tool holder system for secure access
• Copper rivets reinforce high?stress areas
• Built?in tape holster (fits up to 30' FatMax)
• Made in the USA
• Available for left?handed builders (5080DBLH)

Occidental Leather 5080DB Applications

• Framing and structural carpentry
• General construction and remodeling
• Jobsite layout and measuring
• Fastener and small tool organization

Occidental Leather 5080DB Installation Overview

1. Measure from buckle end to your most?used hole on your current tool belt to determine size.
2. Select the closest mid?range belt size from the chart (Small–XXX?Large).
3. Assemble belt, tool bag, fastener bag, and hammer holder per your handed layout.
4. Position pouches for balance, then fasten the belt at the midpoint hole.
5. Load essential tools and adjust for comfort and access.

Key Features

• Round-bottom, two-ply foam core bags hold shape empty or loaded
• Hand-specific tool holder layout optimizes working rhythm
• Function-engineered for trim, finish, and light framing tasks
• Padded nylon 3" belt with 12-oz belting leather tongue & steel roller buckle
• Includes Oxy Tool Shield for sharp tool protection
• Includes 2-in-1 Tool & Hammer Holder
• Available in right- or left-hand setups

Applications

• Trim and finish carpentry
• Light framing
• Cabinetry and interior installs
• Detail work in tight spaces

Installation Overview

1. Measure your current tool belt from buckle end to the commonly used hole to select size (or add 4" to pant waist as an estimate).
2. Wear the set over typical work clothing and buckle at the midpoint hole.
3. Place tool bag on dominant-hand side; fastener bag on the opposite side (swap for left-handed use).
4. Attach the Tool & Hammer Holder and Oxy Tool Shields as preferred.
5. Adjust belt fit and bag spacing for comfort and balance.

Occidental Leather 9855 Key Features

• FatLip bag mouth stays open and resists abrasion
• 10" deep main bags with full leather boot for durability
• Adjust-to-Fit belt for fast sizing and comfortable support
• 24 pockets and tool holders for organized storage
• High-density neoprene, rugged nylon, and full-grain leather build
• Rear 2-in-1 Tool & Hammer Holder and Oxy Tool Shield included
• Made in the USA

Occidental Leather 9855 Applications

• Framing and rough carpentry on residential or light commercial jobs
• General construction and remodeling tool carry
• Finish carpentry organization and fastener management
• Jobsite setups requiring left- or right-hand layouts

Occidental Leather 9855 Installation Overview

1. Measure and adjust the belt to your fit using the Adjust-to-Fit system.
2. Position tool and fastener bags on preferred sides (right or left layout).
3. Attach the 2-in-1 Tool & Hammer Holder and Oxy Tool Shield to the belt.
4. Load tools and fasteners; verify weight is balanced for comfort.
5. Secure buckle and check D-rings and attachments before use.

Occidental Leather 9515 Key Features

• Adjust-to-Fit design accommodates seasonal clothing changes
• D-rings pre-installed for suspender attachment
• Hand-specific tool holders for efficient workflow
• Padded, two-ply OxyLight bags hold shape and reduce sag
• Rugged industrial nylon with leather tool holders and corner reinforcement
• Fixed-bag layout prevents pouch shifting
• Removable High Mount Hammer Holder (5059)
• Made in the USA

Applications

• Framing and general carpentry
• Organizing and carrying tools and fasteners on the jobsite
• Use with suspenders for additional load distribution

Installation Overview

1. Adjust belt to fit over typical work clothing (32"–41" pant waist).
2. Place tool bag on dominant-hand side and fastener bag on the opposite.
3. Attach the hammer holder and any suspenders to the pre-installed D-rings.
4. Load tools and fasteners; verify bags are fixed and secure.

Occidental Leather 8585XL Features

• Hand-specific tool holders for efficient workflow
• Padded two-ply bags keep their shape when empty or loaded
• Extremely abrasion-resistant industrial nylon with leather reinforcements
• FatLip leather mouth stays open & protects against wear
• Full leather boot for rugged durability
• 3″ HD Ranger Belt for comfort and stability
• Available left-handed as 8585LH
• Made in the USA

Occidental Leather 8585XL Applications

• Framing and production carpentry
• General construction and remodeling
• Organized storage of tools and fasteners on site

Occidental Leather 8585XL Installation Overview

1. Measure an existing tool belt from buckle end to your most-used hole to find size.
2. Select Extra Large if the midpoint is about 45″ (approx. pant waist 40″–44″).
3. Place the tool bag on your dominant side and the fastener bag on the opposite side.
4. Buckle and adjust the 3″ Ranger Belt over typical work clothing for a secure fit.

Occidental Leather 9596 Key Features

• NoSpill™ leather tool holders form to tools and help prevent drops
• Hand-specific organization for efficient workflow
• Adjust-to-Fit belt for 32"–40" waists
• Ergonomic design for balanced weight and all-day comfort
• All-leather bag construction; built for long-term jobsite use
• Made in the USA

Occidental Leather 9596 Applications

• Industrial and commercial electrical installations
• Service calls and troubleshooting
• Rough-in and trim-out electrical work
• General jobsite tool and fastener organization

Occidental Leather 9596 Installation Overview

1. Measure your current tool belt from the buckle end to the used hole to confirm sizing.
2. Set the Adjust-to-Fit belt to your measurement (within 32"–40" range).
3. Position pouches and holders for hand-specific access.
4. Secure the belt at the midpoint hole for best adjustment range.
5. Load tools and confirm comfort and balance before use.

Occidental Leather 9540 Key Features

• Hand-specific tool holders for efficient workflow
• Two-ply, foam-core bags keep their shape when empty or loaded
• Abrasion-resistant industrial nylon construction
• Adjust-to-Fit design allows quick sizing changes for seasonal clothing
• D-rings pre-installed for use with suspension systems
• Left-handed model available as 9540LH
• Includes Oxy™ Tool Shields for sharp tool protection
• Made in USA

Occidental Leather 9540 Applications

• Finish carpentry — organized storage for precision tools
• Trim work — compact fastener capacity with speed square holster
• Light framing — balanced layout for everyday jobsite tasks
• Remodeling — lightweight rig for all-day wear
• General carpentry — hand-specific holders for common tools

Occidental Leather 9540 Installation Overview

1. Size the belt: Adjust the buckle to fit pant waist sizes 32"–41".
2. Position bags: Set fastener bag on left and tool bag on right for standard layout.
3. Attach hammer holder: Install the removable high-mount holder at center back.
4. Clip Tool Shields: Secure 2003 Oxy Tool Shields to bag edges or pocket as needed.
5. Connect suspenders if used: Clip to pre-installed D-rings.
6. Load tools and fasteners: Distribute weight evenly and confirm secure fit.

Occidental Leather 8086 OxyLights Ultra Framer Features

• Designed with hand-specific tool holders
• Padded two-ply bags maintain structure
• Extremely abrasion-resistant industrial nylon
• Leather tool holders & corner reinforcement (NoSpill design)
• 7-pouch compact system with patented 2-in-1 outer pouch
• Available in left- or right-hand configurations (8086LH for lefties)
• Made in USA

Occidental Leather 8086 OxyLights Ultra Framer Applications

• Framing – carry nails, layout tools, and a hammer within reach
• Carpentry – organize hand tools, fasteners, and measuring gear
• Remodeling – lightweight setup for all-day wear
• Jobsite tool organization – keep essentials accessible and secure

Occidental Leather 8086 OxyLights Ultra Framer Installation Overview

1. Measure your current tool belt from buckle end to the hole you use.
2. Match that measurement to the size chart midpoint (SM–XXXL).
3. If no belt to measure, add 4″ to your pant waist for an approximate mid range.
4. Select left- or right-hand configuration as preferred.
5. Load tools and adjust belt to the midpoint hole for optimal fit.

Occidental Leather 9550 Key Features

• Premium top-grain leather bags; rugged nylon belt with neoprene padding
• Adjust-to-Fit sizing for 32"–41" pant waists
• Hand-specific tool holders for efficient workflow
• Fixed-position bags to prevent shifting
• Copper rivets reinforce high-stress areas
• D-rings pre-installed for suspension systems
• Removable high-mount hammer holder
• Made in USA

Occidental Leather 9550 Applications

• Framing carpentry and rough construction tasks
• Organizing tools and fasteners for daily jobsite use
• Professional builders needing adjustable, stable carry

Occidental Leather 9550 Installation Overview

1. Adjust the belt within the 32"–41" range to your preferred fit.
2. Lock the crossover adjustment to secure sizing.
3. Position and attach the bags and hammer holder in fixed locations.
4. Connect suspenders to D-rings if using a suspension system.

Occidental Leather 8080DB Features

• Hand-specific tool holder layout improves workflow
• Padded two?ply nylon pouches maintain structure loaded or empty
• Industrial nylon body resists abrasion for long service life
• Leather tool holders and corner reinforcement for durability
• Includes heavy-duty hammer holder
• Made in the USA

Occidental Leather 8080DB Applications

• Framing and general carpentry
• Remodeling and residential construction
• Jobsite tool and fastener organization
• Right- or left-handed belt setups

Occidental Leather 8080DB Installation Overview

1. Measure your current tool belt from buckle end to the commonly used hole to determine midpoint size (or add 4" to pant waist for an estimate).
2. Select the corresponding belt size (Small–XXXL) and fit to the midpoint hole.
3. Slide the tool and fastener bags onto the belt and position for hand preference.
4. Attach the hammer holder at the rear or preferred location.
5. Tighten the belt and make final adjustments for comfort and access.

Occidental Leather 9855LH Key Features

• Adjust-to-Fit™ belt accommodates seasonal clothing changes
• D rings pre-installed for use with suspension systems
• Hand-specific tool holders for left-handed workflow
• FatLip™ bag design with structured mouth for easy access
• Leather-reinforced corners and bottoms for long service life
• Includes rear 2-in-1 Tool & Hammer Holder and Oxy™ Tool Shield
• Made in USA

Occidental Leather 9855LH Applications

• Framing belt system for production carpentry
• General carpentry tool organization on the jobsite
• Left-handed tradespeople needing hand-specific pouch layout

Occidental Leather 9855LH Installation Overview

1. Measure and adjust the belt using the Adjust-to-Fit™ sizing (32"–41").
2. Position tool and fastener bags on the left/right per left-handed layout.
3. Attach included holders (hammer, Oxy™ Tool Shield) to preferred spots.
4. Load tools and fasteners; verify balanced fit and comfort.

Occidental Leather 8003SM Key Features

• 3 in. padded industrial-nylon belt body for balance and comfort
• 2 in. heavy-duty leather tongue with nickel-plated steel roller buckle
• Lightweight, flexible construction for reduced fatigue
• Compatible with most tool/fastener bags and suspenders
• Made in USA

Occidental Leather 8003SM Applications

• Base belt for attaching tool and fastener bags
• Padded support for heavy jobsite loads
• Use with suspenders to spread weight and improve comfort

Occidental Leather 8003SM Installation Overview

1. Measure your current tool belt from the buckle end to the hole you use.
2. Select size Small if your midpoint is 34 in.; allows about 4 in. adjustment either way.
3. Wear over typical work clothing and attach tool/fastener bags or suspenders.

Occidental Leather B9588 Key Features

• Premium top-grain leather bags with reinforced corners
• Adjust-to-Fit belt for pant waist sizes 32"–40"
• Pre-installed D-rings compatible with suspension systems
• Hand-specific tool holders to maximize workflow
• 22 total pockets & tool holders for organized storage

Occidental Leather B9588 Applications

• General carpentry and framing tool organization
• Remodeling and finish work requiring quick tool access
• Jobsite setups needing an adjustable, supportive belt

Occidental Leather B9588 Installation Overview

1. Adjust belt to pant waist size 32"–40" and secure buckle.
2. Position fastener and tool bags to preferred sides.
3. Attach to suspension system if using D-rings.
4. Load tools and fasteners into dedicated holders.
5. Check fit and balance; re-adjust for comfort as needed.

Occidental Leather B5625XL Features

• Lightweight 100% premium top?grain leather construction
• Hand?specific tool holders for efficient workflow
• NoSpill tool holder system helps prevent drops
• Reinforced back walls at stress points for durability
• Side?by?side tape holster and upper bag for quick access
• Includes 2?in?1 Tool & Hammer holster
• Left?handed version available (B5625LH)
• Made in the USA

Occidental Leather B5625XL Applications

• Framing and carpentry tool organization
• General construction and jobsite workflow
• Fastener and hand?tool storage for builders

Occidental Leather B5625XL Installation Overview

1. Size the belt using the mid?range sizing chart (measure from buckle end to your used hole).
2. Attach the fastener and tool bags to the belt; position for right or left?hand workflow.
3. Install the 2?in?1 Tool & Hammer holder and Oxy Tool Shields in the desired pockets.
4. Load tools and fasteners; adjust belt for comfort and balance.
5. Confirm secure fit and accessibility before use.

Key Features

• Hand-specific tool holder layout for efficiency
• Padded two-ply bags keep their shape
• Extremely abrasion-resistant industrial nylon
• Leather tool holders with reinforced corners
• Patented 2-in-1 outer pouch for fast organization
• Available in right- or left-hand configurations (8086LH)

Applications

• Framing and general carpentry tool & fastener carry
• Jobsite organization for production builders
• Daily use where lightweight durability is needed

Installation Overview

1. Lay your current tool belt flat and measure from buckle end to the most-used hole.
2. Select the size whose midpoint matches your measurement (Small midpoint: 34″).
3. If you don’t have a belt, add about 4″ to your pant waist for an approximate midpoint.
4. Adjust buckle for a secure fit over typical work clothing.

Occidental Leather B5625XXL Key Features

• Lightweight 100% premium top-grain leather — no break-in required
• Hand-specific tool holders for natural workflow
• NoSpill holder system keeps tools secure
• Reinforced back walls at stress points for extended wear
• Side-by-side upper bag & tape mount for streamlined access
• Made in the USA

Occidental Leather B5625XXL Applications

• Framing carpentry setups requiring fast access to nails & tools
• General construction and remodel work
• Jobsite organization for levels, squares, chisels, and drivers
• Daily professional use where durability and balance are essential

Occidental Leather B5625XXL Installation Overview

1. Measure an existing tool belt from buckle end to your most?used hole.
2. Match that measurement to the size chart’s mid?range value.
3. If no belt to measure, add 4" to your pant waist for an approximate mid?range.
4. Adjust the belt to the midpoint hole; allow 4" of adjustment each side.
5. Load tools into hand-specific holders and secure with NoSpill system.

Occidental Leather B5625XXL Key Features

• Lightweight 100% premium top-grain leather — no break-in required
• Hand-specific tool holders for natural workflow
• NoSpill holder system keeps tools secure
• Reinforced back walls at stress points for extended wear
• Side-by-side upper bag & tape mount for streamlined access
• Made in the USA

Occidental Leather B5625XXL Applications

• Framing carpentry setups requiring fast access to nails & tools
• General construction and remodel work
• Jobsite organization for levels, squares, chisels, and drivers
• Daily professional use where durability and balance are essential

Occidental Leather B5625XXL Installation Overview

1. Measure an existing tool belt from buckle end to your most?used hole.
2. Match that measurement to the size chart’s mid?range value.
3. If no belt to measure, add 4" to your pant waist for an approximate mid?range.
4. Adjust the belt to the midpoint hole; allow 4" of adjustment each side.
5. Load tools into hand-specific holders and secure with NoSpill system.

Occidental Leather 8585XL Features

• Hand-specific tool holders for efficient workflow
• Padded two-ply bags keep their shape when empty or loaded
• Extremely abrasion-resistant industrial nylon with leather reinforcements
• FatLip leather mouth stays open & protects against wear
• Full leather boot for rugged durability
• 3″ HD Ranger Belt for comfort and stability
• Available left-handed as 8585LH
• Made in the USA

Occidental Leather 8585XL Applications

• Framing and production carpentry
• General construction and remodeling
• Organized storage of tools and fasteners on site

Occidental Leather 8585XL Installation Overview

1. Measure an existing tool belt from buckle end to your most-used hole to find size.
2. Select Extra Large if the midpoint is about 45″ (approx. pant waist 40″–44″).
3. Place the tool bag on your dominant side and the fastener bag on the opposite side.
4. Buckle and adjust the 3″ Ranger Belt over typical work clothing for a secure fit.

Occidental Leather 8071XL Key Features

• Extra Long back strap for 5592 Beltless™ Retro Kit
• 6" longer than the 8071
• Heavy-duty construction
• Made in USA

Occidental Leather 8071XL Applications

• Replace or upgrade the back strap on the 5592 Beltless™ Retro Kit
• Extend fit for larger frames or layered clothing
• Increase bag swing and mobility on beltless setups

Occidental Leather 8071XL Installation Overview

1. Remove the standard back strap from the 5592 Beltless™ Retro Kit.
2. Attach the 8071XL to the existing connection points.
3. Adjust the strap length for preferred fit and movement.
4. Confirm secure attachment before use.

Occidental Leather 5080DB Features

• Premium top?grain leather for weather?resistant durability
• Hand?specific tool layout to maintain work rhythm
• Copper?riveted stress points on main bags
• NoSpill tool holder system keeps tools secure
• Function?engineered setup for modern builders
• Left?handed version available (5080DBLH)

Occidental Leather 5080DB Applications

• Framing and general carpentry
• Jobsite fastening, layout, and measuring
• Organized carry of hand tools, nails, and fasteners

Occidental Leather 5080DB Installation Overview

1. Measure an existing tool belt from buckle end to your most?used hole to find size.
2. Select the belt size closest to that midpoint measurement (or add ~4" to pant size if no belt).
3. Place tool bag on dominant hand side; fastener bag on opposite side.
4. Adjust belt for comfort and even weight distribution.

Occidental Leather 5087SM Features

• Premium top-grain leather with oil & wax tanning for outdoor performance
• Hand-specific tool layout; tape holder on the left
• Copper rivet reinforcement at main bags
• NoSpill tool holder system keeps tools secure
• Function-engineered design for professional builders
• Available left-handed layout option: 5087LH

Occidental Leather 5087SM Applications

• Framing and rough carpentry
• General carpentry tool and fastener organization
• Jobsite use in outdoor conditions
• Right-handed users preferring tape on left side
• Left-handed setup available for opposite layout

Occidental Leather 5087SM Installation Overview

1. Lay your current tool belt flat and measure from buckle end to your most-used hole.
2. Select the size closest to that midpoint measurement (Small is 34″ mid range).
3. If no belt is available, add 4″ to your pant waist for an approximate mid range.
4. Adjust the belt on the midpoint hole; fine-tune using the remaining holes.
5. Arrange tool and fastener bags per your dominant hand preference.

Occidental Leather 5191XL Key Features

• Unique one-piece buscadero belt design for even weight distribution
• Premium top?grain leather with copper?riveted stress points
• Hand?specific tool holders with NoSpill tool holder system
• Sheepskin?lined interior for enhanced comfort
• Function?engineered layout based on 5060 fastener bag & 5018 tool bag
• Made in USA
• Not available as a left?hand model (suggest 9550LH)

Occidental Leather 5191XL Applications

• Framing and general carpentry tool carry
• Remodeling and residential construction
• Jobsite organization for fasteners, hand tools, and layout gear
• Pro-grade daily wear where comfort and durability are critical

Occidental Leather 5191XL Installation Overview

1. Put on the belt over your typical work clothing and note the hole you use.
2. Remove the belt and measure from the end of the buckle to the used hole.
3. Select the size whose mid?range matches your measurement; belts allow about 4" of adjustment each way.
4. If between sizes, choose the larger size for best fit.

Occidental Leather 8071 Key Features

• Back strap designed ONLY for the 5592 Beltless™ Retro Kit
• Heavy-duty, contractor-grade construction
• Adjustable buckle for quick fit tuning
• Leather keeper loops with snap hardware
• Made in USA

Occidental Leather 8071 Applications

• Replacement back strap for the 5592 Beltless™ Retro Kit
• Stabilizes beltless tool bag systems
• Enhances carrying comfort during long wear
• Keeps bags positioned for better accessibility

Occidental Leather 8071 Installation Overview

1. Attach the strap to the 5592 Beltless™ Retro Kit connection points.
2. Thread through the buckle and set desired length.
3. Secure leather keepers/snaps and check all hardware engagement.
4. Test fit and re-adjust for comfort and stability.

Occidental Leather 8585M Features

• Hand-specific tool holder layout for efficient workflow
• Padded two-ply tool bags maintain shape
• Extremely abrasion-resistant industrial nylon exterior
• Leather tool holders & corner reinforcement
• FatLip leather mouth keeps bag formed & open
• Full leather boot for durability
• 3″ HD Ranger work belt for comfort & stability
• Rear 2-in-1 Tool & Hammer Holder
• Available for left-handed builders as 8585LH

Occidental Leather 8585M Applications

• Production carpentry needing quick access & organization
• Framing tasks with mixed fasteners & common hand tools
• General construction and jobsite tool carry

Occidental Leather 8585M Installation Overview

1. Measure from the end of your buckle to the hole you use on your current tool belt.
2. Choose the size closest to that midpoint measurement (Medium — 37″).
3. Place the tool bag on your dominant-hand side and the fastener bag opposite; adjust belt for a secure fit.

Key Features

• Wide 5″ belt for enhanced back support
• Built‑in suspender attachment loops
• Thick padded wool liner for comfort & moisture wicking
• 2″ all‑leather overbelt with heavy duty loops to minimize bag sliding
• Nickel‑plated steel buckles
• Edge stitching on leather for added strength
• Made in USA

Applications

• Supportive base belt for carpenter and contractor tool rigs
• Comfort upgrade for long days carrying loaded tool bags
• Secure attachment of fastener & tool bags with overbelt
• Compatible with suspenders for improved load distribution
• General construction, framing, finish work

Installation Overview

1. Measure your current tool belt from buckle end to the hole used to determine size.
2. Select the Large size and adjust to midpoint hole for optimal fit.
3. Attach tool bags to the 2″ overbelt and position loops to prevent sliding.
4. Fasten the nickel‑plated buckle and check suspender loop placement.
5. Confirm comfortable fit over typical work clothing.

Occidental Leather 5135 XXL Key Features

• Wide 5” belt provides enhanced back support
• Padded wool liner for moisture-wicking comfort
• 2” all-leather overbelt keeps tool bags from sliding
• Nickel-plated steel buckles and hardware
• Built-in suspender attachment loops
• Edge-stitched leather for added strength
• Made in the USA

Occidental Leather 5135 XXL Applications

• Securing and supporting tool bags on the job
• Carpentry and framing work requiring all-day wear
• Electrical and mechanical trades needing stable rig support
• General construction where comfort & load distribution matter

Occidental Leather 5135 XXL Installation Overview

1. Measure and select the correct belt size; fasten at the midpoint hole.
2. Thread tool bag loops onto the 2” overbelt and position as desired.
3. Buckle the belt snugly at working height over jobsite clothing.
4. Attach suspenders to the built-in loops if using for heavier loads.
5. Make final fit adjustments for comfort and balance.

Occidental Leather 8080DBLHXXL Key Features

• 20 pockets & tool holders for organized storage
• Hand-specific NoSpill™ leather tool holders keep tools secure
• Padded, two-ply bags maintain shape and comfort
• Industrial nylon body with leather tool holders and reinforced corners
• HD 3" Ranger Work Belt included
• Made in USA
• Left-handed layout; Double outer bag design

Occidental Leather 8080DBLHXXL Applications

• Framing and rough carpentry
• General construction and remodeling
• Jobsite tool and fastener organization
• Left-handed workflows requiring hand-specific layout

Occidental Leather 8080DBLHXXL Installation Overview

1. Size the HD 3" Ranger belt to your work clothing and fasten securely.
2. Position the tool bag on the left and fastener bag on the right for a left-handed setup.
3. Load essential tools and fasteners into dedicated pockets and holders.
4. Place hammer in the rear holder and tape in the built-in tape holster.
5. Adjust for comfort and even weight distribution before use.

Occidental Leather 9515LH Key Features

• Adjust-to-Fit design for seasonal clothing changes (32"–41" pant waist)
• Left-handed, hand-specific tool layout
• Padded two-ply bags that hold their shape; fixed bag design prevents shifting
• Industrial nylon with leather tool holders and reinforced corners
• D-rings pre-installed for suspender systems
• Removable High Mount Hammer Holder included
• Made in the USA

Occidental Leather 9515LH Applications

• Framing and rough carpentry tool carry
• General construction and remodel jobsite organization
• Left-handed workflow optimization with hand-specific pouch placement
• Use with suspenders for added load support

Occidental Leather 9515LH Installation Overview

1. Adjust belt to fit over typical work clothing within the 32"–41" range.
2. Wear tool bag on left and fastener bag on right for left-handed use.
3. Attach the removable High Mount Hammer Holder at the rear.
4. Clip suspenders to the pre-installed D-rings if desired.
5. Load tools and confirm secure, comfortable fit.

Key Features

• 5" wide belt for enhanced lumbar support
• Padded wool liner for comfort & moisture wicking
• 2" all-leather overbelt minimizes bag movement
• Nickel-plated steel buckles & hardware
• Built-in suspender attachment loops
• Edge-stitched construction
• Made in the USA

Applications

• Daily tool carry for construction and trades
• Carpentry and framing rigs needing strong back support
• Electrical, plumbing, and finish work with multiple pouches
• Use with suspenders for balanced load distribution

Installation Overview

1. Confirm XXL sizing using the belt-size guide.
2. Thread tool bags onto the 2" overbelt and position.
3. Buckle the belt where you normally wear it and tighten.
4. Attach compatible suspenders to the built-in loops if desired.
5. Adjust using the strap holes for a secure, comfortable fit.

Key Features

• Wide 5” belt for enhanced back support
• Padded wool liner for moisture-wicking comfort
• 2” all-leather overbelt secures tool bags
• Heavy-duty, nickel-plated steel buckles and hardware
• Built-in suspender attachment loops
• Edge-stitched leather for strength and clean finish
• Made in the USA

Applications

• Jobsite tool carry with improved back support
• Secure attachment of tool bags for carpentry and trades
• Comfortable wear for long shifts with moisture control
• Use with suspenders for balanced load distribution

Installation Overview

1. Measure your current tool belt per sizing guide to confirm Small.
2. Buckle the belt at your typical working position over clothing.
3. Thread and tighten the 2” overbelt to lock tool bags in place.
4. Attach compatible suspenders to the built-in loops if needed.
5. Adjust for comfort and verify secure fit before use.

Occidental Leather B5135 XL Features

• Wide 5″ belt for enhanced back support
• Thick padded wool liner for comfort and moisture management
• 2″ all–leather overbelt with loops to minimize bag sliding
• Nickel–plated steel buckles and hardware
• Suspender attachment loops
• Edge–stitched construction for strength and clean finish
• Made in the USA

Occidental Leather B5135 XL Applications

• Stabilizing and supporting tool bags for daily jobsite use
• Carpentry, framing, and finish work requiring extended wear
• Use with suspenders for balanced weight distribution
• General construction and remodeling tasks

Occidental Leather B5135 XL Installation Overview

1. Measure your existing tool belt from buckle to the hole used to confirm size.
2. Wear over typical work clothing and fasten at the midpoint hole.
3. Attach tool bags to the overbelt and secure through belt loops.
4. Clip compatible suspenders to the built–in loops if desired.

Key Features

• Wide 5″ belt for enhanced back support
• Suspender attachment loops
• Thick padded wool liner for comfort & moisture wicking
• Heavy-duty buckles & belt loops minimize bag sliding
• Edge-stitched leather for added strength
• Made in USA

Applications

• Supportive work belt for carrying tool bags on the jobsite
• Compatible with suspenders for heavier load distribution
• Comfort-focused rig for framing, carpentry, and general construction
• Moisture-wicking liner ideal for all-day wear in variable conditions

Installation Overview

1. Measure the belt you currently wear where you use it over work clothes.
2. Note the hole used to fasten; remove belt and lay flat.
3. Measure from the end of the buckle to the used hole to confirm size.
4. Buckle at the midpoint hole; adjust 4″ either direction for fit.
5. Attach suspenders to loops and secure tool bags to the overbelt.

Occidental Leather 5135 SM Features

• Wide 5" belt for enhanced lower?back support
• Thick padded wool liner for comfort and moisture wicking
• 2" all?leather overbelt keeps tool bags locked in place
• Nickel?plated steel buckles and robust belt loops minimize bag sliding
• Edge?stitched leather for added strength and clean finish
• Suspender attachment loops integrated
• Made in the USA

Occidental Leather 5135 SM Applications

• Daily tool carry for carpenters, framers, and general trades
• Jobs requiring strong back support and secure bag retention
• Use with suspenders for heavier loadouts

Occidental Leather 5135 SM Installation Overview

1. Measure a belt you wear at work from buckle end to the hole used; match size.
2. Wear over typical work layers and fasten near the midpoint hole for adjustability.
3. Attach tool bags to the 2" overbelt and position as preferred.
4. Clip suspenders to built?in loops if added support is needed.

Key Features

• 5″ wide belt for enhanced back support
• Padded wool liner for moisture?wicking comfort
• 2″ all?leather overbelt helps prevent bag sliding
• Nickel?plated steel buckles & hardware
• Built?in suspender attachment loops
• Edge?stitched construction for strength and clean finish
• Made in the USA

Applications

• Daily use with carpenter and framer tool rigs
• General construction and remodeling setups
• Electrical, HVAC, and trim work where belt?mounted bags are used
• Jobs requiring suspender?compatible load distribution
• Comfort upgrade for heavy tool carry on site

Installation Overview

1. Measure your existing tool belt from buckle end to the used hole to confirm Large (approx. 41″ midpoint).
2. Position the belt over work clothing and fasten at the midpoint hole for optimal adjustment.
3. Thread and secure tool bags onto the 2″ overbelt; tighten to minimize sliding.
4. Attach suspenders to the integrated loops if extra load support is needed.
5. Check fit and comfort; adjust buckle and overbelt tension as required.