Framing Tool Belts & Carpenter Bags

Occidental Leather 1546 Features

• Ultra-light industrial nylon construction for reduced fatigue
• Chest-height pockets for pencils and clip-on accessories
• Even weight distribution for all-day comfort
• Heavy-duty spring clips for quick attachment and removal
• Slides onto your tool belt for easy setup
• Leather loop attachment system fits up to 3" tool belts
• Made in USA

Occidental Leather 1546 Applications

• Support and distribute tool belt weight on the shoulders
• Keep small tools and pencils accessible at chest height
• Enhance comfort during prolonged wear on jobsites

Occidental Leather 1546 Installation Overview

1. Slide suspenders onto the tool belt using the leather loop attachment points (fits up to 3" belts).
2. Clip the heavy-duty spring clips to the belt or attachment loops.
3. Adjust shoulder and front straps for a balanced, comfortable fit.
4. Stow pencils or clip-on items in the chest pockets.

Key Features

• Hand-specific tool holders for efficient workflow
• Padded two-ply bags maintain shape when empty or loaded
• Industrial nylon exterior with leather holders and reinforced corners
• FatLip leather mouth keeps bags open and resists wear
• Full leather boot for rugged longevity
• 3" HD ranger belt with center 2?in?1 tool & hammer holder
• Pockets & tool holders: 25
• Made in the USA

Applications

• Framing and production carpentry
• General construction and remodeling
• Jobsite tool and fastener organization
• Left- or right-hand optimized setups for daily use

Installation Overview

1. Measure an existing tool belt from buckle end to your most-used hole to determine size.
2. Select the belt size closest to that midpoint measurement.
3. Position tool bag on dominant hand side and fastener bag opposite.
4. Secure the belt at the midpoint hole; adjust for comfort and balance.
5. Load tools and fasteners by task to optimize workflow.

Key Features

• Pre-riveted leather loops with durable steel D-rings
• Slip-on design attaches suspenders to additional belts
• Fits up to a 3″ work belt
• Compatible with suspenders 1546, 5009 & 5055
• Made in USA

Applications

• Add suspender attachment points to extra work belts
• Swap suspenders between belts without tools
• Improve load distribution on heavy tool belt setups

Installation Overview

1. Slide each loop over the belt at desired attachment points.
2. Position loops evenly for balanced support.
3. Clip suspender hardware to the D-rings.
4. Check belt fit and ensure loops are secure before use.

Occidental Leather 8581 Features

• FatLip™ leather mouth keeps the bag formed, open, and protected
• Full leather boot for long-term durability
• Patented 2-in-1 outer bag with built-in angle square holster
• Tri-square sleeve, cat’s paw loop, and external nail set/driver bit pouches
• 10 pockets & tool holders for efficient organization
• Designed to be worn on the non-dominant side for fastener access
• Made in the USA

Occidental Leather 8581 Applications

• Framing: Keep nails, angle square, and layout tools at hand
• Drywall installation: Store fasteners and driver bits for quick access
• General construction: Organize common hand tools and fasteners
• Remodeling: Versatile pouch setup for mixed trades

Occidental Leather 8581 Installation Overview

1. Thread the bag onto a compatible 3″ work belt.
2. Position on the non-dominant side for fastener access.
3. Load tools and fasteners into main, outer, and upper pockets.
4. Seat the angle square in the integrated holster; place tri-square and cat’s paw in their sleeves.
5. Verify comfortable reach and balance before use.

Occidental Leather 8003 Key Features

• 3" wide padded nylon belt body for balanced load support
• 2" heavy-duty leather tongue with nickel-plated steel roller buckle
• Lightweight industrial nylon reduces fatigue
• Works with most tool and fastener bags; suspenders compatible
• Made in USA

Occidental Leather 8003 Applications

• Foundation belt for tool and fastener bag setups
• Daily jobsite wear requiring comfort and support
• Use with suspenders for heavier rigs

Occidental Leather 8003 Installation Overview

1. Measure your current tool belt from buckle end to the hole you use most.
2. Select the size closest to that midpoint measurement.
3. Attach your tool/fastener bags and suspenders as needed.
4. Adjust to the midpoint hole; fine-tune within the 4" range.

Occidental Leather 2003 Key Features

• Clip-on convenience for bags or pockets
• Protects tools, bags, and body from sharp edges
• Holds a chisel, knife, or diagonal cutter plus one pencil
• Compact, lightweight, jobsite-ready build
• Fits most Occidental Leather bags and many other tool bags

Occidental Leather 2003 Applications

• Safe storage of sharp hand tools on tool belts or bags
• Protecting clothing and pouches from blade damage
• Keeping chisels and cutters accessible while preventing injury
• Organizing a pencil alongside a primary cutting tool

Occidental Leather 2003 Installation Overview

1. Attach the shield by clipping it onto a tool bag edge or pocket.
2. Insert the chosen tool into the main compartment until fully seated.
3. Place one round pencil into the integrated slot if desired.
4. Confirm the clip is secure and the tool is retained before use.

Occidental Leather 5062 Key Features

• 4-pouch stacked layout for expanded capacity
• 10 pockets and tool holders sized for fasteners and layout gear
• Dedicated slots for 1" blade square, angle square, driver bits, and cat’s paw
• Full-grain leather construction for durability
• Designed to be worn on the non-dominant side
• Made in the USA

Occidental Leather 5062 Applications

• Framing and general carpentry fastener storage
• Organizing layout tools and driver bits on belt
• Daily jobsite use where rugged leather pouches are preferred

Occidental Leather 5062 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the non-dominant side for balanced access.
3. Load fasteners and tools into the designated pockets and holders.
4. Check that the pouch is secure and pockets are seated before work.

Key Features

• Hand-specific tool holder layout for efficient workflow
• Padded two-ply bags maintain shape
• Abrasion-resistant industrial nylon with OxyRed leather reinforcements
• NoSpill leather tool holders for secure access
• Made in the USA

Applications

• Framing and general carpentry
• Jobsite tool and fastener organization
• Rough construction and remodeling
• Left- or right-handed setups for professional builders

Installation Overview

1. Measure your current tool belt from buckle end to the hole you use most.
2. Match that measurement to the size chart midpoint (SM–XXXL).
3. Assemble belt, tool bag, fastener bag, and hammer holder per your handedness.
4. Adjust to the midpoint hole for best fit, with about 4" of adjustment each way.
5. Load tools and fasteners; verify balance and accessibility.

Occidental Leather 5080DB Features

• Premium top?grain leather for tough, outdoor jobsite use
• Hand?specific tool layout to promote natural working rhythm
• NoSpill tool holder system for secure access
• Copper rivets reinforce high?stress areas
• Built?in tape holster (fits up to 30' FatMax)
• Made in the USA
• Available for left?handed builders (5080DBLH)

Occidental Leather 5080DB Applications

• Framing and structural carpentry
• General construction and remodeling
• Jobsite layout and measuring
• Fastener and small tool organization

Occidental Leather 5080DB Installation Overview

1. Measure from buckle end to your most?used hole on your current tool belt to determine size.
2. Select the closest mid?range belt size from the chart (Small–XXX?Large).
3. Assemble belt, tool bag, fastener bag, and hammer holder per your handed layout.
4. Position pouches for balance, then fasten the belt at the midpoint hole.
5. Load essential tools and adjust for comfort and access.

Key Features

• 10" deep main pouch for high capacity
• FatLip leather-reinforced mouth stays open and resists wear
• Full leather boot adds structure and durability
• 13 pockets & tool holders for organized access
• Right-hand layout; worn on the right side
• Made in the USA

Applications

• Daily carry of hand tools such as hammer, knife, pencils, and chisels
• Carpentry/framing setups on the dominant-hand side
• General construction and remodeling tool organization

Occidental Leather 5060 Features

• Three stacked pouches with top-access tier for efficient fastener storage
• 9 pockets and tool holders for layout tools and bits
• Dedicated holders fit cat’s paw, driver bits, angle square, and 1" blade square
• Premium, reinforced leather construction
• Available in left- or right-hand setups and multiple colors
• Made in the USA

Occidental Leather 5060 Applications

• Framing: Keep nails and layout tools at hand
• General carpentry: Organized storage for daily tools and fasteners
• Jobsite setup: Streamlined access to squares, bits, and cat’s paw

Occidental Leather 5060 Specifications

Key Features

• Round-bottom, two-ply foam core bags hold shape empty or loaded
• Hand-specific tool holder layout optimizes working rhythm
• Function-engineered for trim, finish, and light framing tasks
• Padded nylon 3" belt with 12-oz belting leather tongue & steel roller buckle
• Includes Oxy Tool Shield for sharp tool protection
• Includes 2-in-1 Tool & Hammer Holder
• Available in right- or left-hand setups

Applications

• Trim and finish carpentry
• Light framing
• Cabinetry and interior installs
• Detail work in tight spaces

Installation Overview

1. Measure your current tool belt from buckle end to the commonly used hole to select size (or add 4" to pant waist as an estimate).
2. Wear the set over typical work clothing and buckle at the midpoint hole.
3. Place tool bag on dominant-hand side; fastener bag on the opposite side (swap for left-handed use).
4. Attach the Tool & Hammer Holder and Oxy Tool Shields as preferred.
5. Adjust belt fit and bag spacing for comfort and balance.

Occidental Leather 5020 Features

• Dual-function design: integrated hammer loop plus pocket for a hand tool
• Space-saving footprint to free up room on your belt
• 12 oz English bridle leather for long-term durability
• Slides onto standard tool belts for quick setup
• Heavy-duty stitching and metal rivets for jobsite toughness
• Made in the USA

Occidental Leather 5020 Applications

• Carry a hammer and primary hand tool together on one holder
• Framing, trim, and general carpentry tool belts
• Remodeling and punch-list work where compact carry is key
• Workshop use and weekend DIY tasks
• Jobsite setups needing fast access without adding bulk

Occidental Leather 5020 Installation Overview

1. Thread the holder onto your tool belt at the preferred position.
2. Orient the pocket and loop for dominant-hand access.
3. Seat the hammer in the front loop and place a hand tool in the pocket.
4. Check that tools hang freely with no interference while walking or kneeling.
5. Reposition on the belt if needed for balance and comfort.

Occidental Leather 5005L Key Features

• .75"+ thick sheepskin pads for cushioned support
• Moisture-wicking wool keeps you dry and comfortable
• Natural insulation—comfortable year-round
• Adjustable straps fit belts up to 3" wide
• Requires 1–2" extra belt length for proper fit
• Made in USA

Occidental Leather 5005L Applications

• Increase comfort when wearing loaded tool belt rigs
• Reduce pressure points during long shifts
• Improve fit for framing, finish, electrical, and roofing setups
• Add insulation and moisture control to any compatible work belt

Occidental Leather 5005L Installation Overview

1. Lay your existing tool belt flat and measure per size chart to confirm fit.
2. Position the liner inside the belt with sheepskin toward the body.
3. Thread and fasten the liner’s adjustable straps around the belt (up to 3" wide).
4. Allow 1–2" extra belt length; secure buckle and check comfort.
5. Attach pouches/holders and verify clearance before use.

Occidental Leather 8018DB Features

• Popular OxyLights 3-pouch layout for everyday tools
• OxyRed leather reinforcement at stress points
• Heavy-duty hammer loop and tape measure holster (up to 35')
• Interior holders for knife, chisel, pencil, lumber crayon, and level
• Designed for right-side wear for right-handed users
• Lightweight nylon/leather hybrid construction; Made in USA

Occidental Leather 8018DB Applications

• Carpentry and framing tool carry
• Finish and trim work organization
• General construction and handyman tool storage
• Right-hand dominant setups needing quick access

Occidental Leather 8018DB Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the right side for dominant-hand access.
3. Load tools into dedicated holders and pouches.
4. Confirm balance and adjust placement for comfort.

Occidental Leather 9855 Key Features

• FatLip bag mouth stays open and resists abrasion
• 10" deep main bags with full leather boot for durability
• Adjust-to-Fit belt for fast sizing and comfortable support
• 24 pockets and tool holders for organized storage
• High-density neoprene, rugged nylon, and full-grain leather build
• Rear 2-in-1 Tool & Hammer Holder and Oxy Tool Shield included
• Made in the USA

Occidental Leather 9855 Applications

• Framing and rough carpentry on residential or light commercial jobs
• General construction and remodeling tool carry
• Finish carpentry organization and fastener management
• Jobsite setups requiring left- or right-hand layouts

Occidental Leather 9855 Installation Overview

1. Measure and adjust the belt to your fit using the Adjust-to-Fit system.
2. Position tool and fastener bags on preferred sides (right or left layout).
3. Attach the 2-in-1 Tool & Hammer Holder and Oxy Tool Shield to the belt.
4. Load tools and fasteners; verify weight is balanced for comfort.
5. Secure buckle and check D-rings and attachments before use.

Occidental Leather 5093 Key Features

• Maximum comfort with wide, padded shoulder support lined with Dri-Lex® to wick perspiration
• Fully adjustable straps for freedom of movement and a one-size-fits-most fit
• Even load distribution to reduce fatigue and help prevent lower back strain
• 25 pockets and tool holders keep essentials organized and within reach
• Hand-specific, right-handed layout with sleeves for clip-on accessories
• Includes rear-mounted 5156 Cradle Hammer Holder
• Made in the USA

Occidental Leather 5093 Applications

• Framing and general carpentry
• Remodeling and rough-in work
• Overhead and ladder tasks requiring balanced load carry
• Long-duration jobs where beltless comfort reduces back strain
• Jobsite setups needing modular, clip-on tool accessories

Occidental Leather 5093 Installation Overview

1. Adjust shoulder straps and chest strap for a snug, comfortable fit.
2. Position tool and fastener bags on the side rings; secure hardware.
3. Attach the 5156 Cradle Hammer Holder to the rear mounting point.
4. Load tools evenly across bags to balance weight.
5. Fine-tune strap tension and verify full range of motion.

Occidental Leather 9515 Key Features

• Adjust-to-Fit design accommodates seasonal clothing changes
• D-rings pre-installed for suspender attachment
• Hand-specific tool holders for efficient workflow
• Padded, two-ply OxyLight bags hold shape and reduce sag
• Rugged industrial nylon with leather tool holders and corner reinforcement
• Fixed-bag layout prevents pouch shifting
• Removable High Mount Hammer Holder (5059)
• Made in the USA

Applications

• Framing and general carpentry
• Organizing and carrying tools and fasteners on the jobsite
• Use with suspenders for additional load distribution

Installation Overview

1. Adjust belt to fit over typical work clothing (32"–41" pant waist).
2. Place tool bag on dominant-hand side and fastener bag on the opposite.
3. Attach the hammer holder and any suspenders to the pre-installed D-rings.
4. Load tools and fasteners; verify bags are fixed and secure.

Key Features

• Quick–disconnect 3" leather belting accepts tool bags with tunnel loops up to 8.5" wide
• Wide padded shoulder support lined with Dri–Lex to wick perspiration
• Fully adjustable straps with quick–release chest buckle
• Even load distribution to lessen fatigue and help prevent lower back strain
• 17 pockets/tool holders keep common tools close at hand
• Extra pockets behind tool holders for hands or gloves
• Heavy–duty D–ring for hanging storage
• Made in USA; left–handed option available

Applications

• Framing without a traditional belt
• Electrical work needing balanced tool carry
• Concrete tasks with frequent tool access
• Trim and finish work in tight spaces

Installation Overview

1. Adjust shoulder straps and chest buckle for comfort.
2. Attach compatible tool bags to the 3" leather belting via tunnel loops (up to 8.5").
3. Organize tools among the 17 holders; secure heavier items to designated loops.
4. Use the D–ring for hanging storage when not in use.
5. Detach bags as needed for finish or tight–space tasks.

Occidental Leather 5006 Key Features

• Natural sheepskin lining for maximum comfort
• Thick harness leather exterior with .75"+ wool padding
• No leading edge to dig into hips or restrict circulation
• Slides under tool bags; fits belts up to 3" wide
• Requires 1–2" additional belt length
• Dimensions of hip area between belt slots: 10" x 6"
• Handmade in USA

Occidental Leather 5006 Applications

• Increase comfort when carrying loaded tool belts
• Distribute belt weight across hips to reduce pressure points
• Add cushioning under tool bags for long workdays
• Upgrade for most 3" and narrower work belts

Occidental Leather 5006 Installation Overview

1. Remove or loosen tool bags from your belt.
2. Slide each pad onto the belt so it sits under the bag location.
3. Allow 1–2" extra belt length for the added padding.
4. Reposition and secure tool bags over the pads.
5. Adjust fit for comfort and even weight distribution.

Occidental Leather 5355 Features

• Suspension system helps shift load from hips to shoulders for reduced fatigue
• Hip Buddies padding softens pressure points for added comfort
• Accepts any bag up to 7.5" wide
• Leather and nylon construction
• Available colors: OxyRed or Black
• Made in USA
• Not compatible with 5525 Big Oxy Fastener Bag, B5611 Green Building Fastener Bag, Adjust?to?Fit systems, or Stronghold Comfort Belts/Systems

Occidental Leather 5355 Applications

• Reduce hip strain when wearing loaded tool belts
• Increase comfort during long days on the jobsite
• Stabilize and balance tool belt weight
• Use with compatible Occidental Leather bag setups up to 7.5" wide

Occidental Leather 5355 Installation Overview

1. Attach Hip Buddies to your belt where support is needed.
2. Clip or fasten the suspension straps to the belt’s attachment points.
3. Adjust front and rear strap lengths for balanced load and comfort.
4. Check bag widths (up to 7.5") and compatibility before use.
5. Secure all buckles and hardware; test fit and make final adjustments.

Occidental Leather 5595 Key Features

• Go beltless with bags that accept a 3" belt
• Works with many traditional Occidental Leather bags for custom setups
• Vest-style suspension helps distribute load off the hips
• Leather and padded components shown for comfort and durability
• Made in USA

Occidental Leather 5595 Applications

• Converting belt-mounted tool bags to a beltless vest system
• Reducing hip strain by distributing tool weight across shoulders and torso
• Customizing carry systems for carpentry, framing, finish work, and general trades

Occidental Leather 5595 Installation Overview

1. Attach compatible tool bags with 3" belt slots to the Beltless Retro hangers.
2. Put on the vest and adjust shoulder, chest, and side straps for a snug fit.
3. Balance load by positioning bags evenly on both sides.
4. Secure all buckles/clips and test range of motion before use.

Occidental Leather 8062 Key Features

• Same features as the 8060 with an added outer pouch
• 10 pockets & tool holders with dedicated storage for squares, driver bits, and cat’s paw
• Streamlined layout for compact carry
• Optimized for left-side wear (fasteners accessed with left hand)
• OxyLights nylon construction with leather reinforcements
• Made in USA

Occidental Leather 8062 Applications

• Framing tasks needing organized fastener access
• General carpentry where compact storage is preferred
• Left-side wear for non-dominant hand tool retrieval
• Jobsite organization for squares, bits, nail sets, and small tools

Occidental Leather 8062 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the left side for non-dominant hand access.
3. Load tools and fasteners into the designated pockets.
4. Confirm the bag is seated securely on the belt.
5. Adjust placement for comfortable reach and balance.

Occidental Leather 8585XL Features

• Hand-specific tool holders for efficient workflow
• Padded two-ply bags keep their shape when empty or loaded
• Extremely abrasion-resistant industrial nylon with leather reinforcements
• FatLip leather mouth stays open & protects against wear
• Full leather boot for rugged durability
• 3″ HD Ranger Belt for comfort and stability
• Available left-handed as 8585LH
• Made in the USA

Occidental Leather 8585XL Applications

• Framing and production carpentry
• General construction and remodeling
• Organized storage of tools and fasteners on site

Occidental Leather 8585XL Installation Overview

1. Measure an existing tool belt from buckle end to your most-used hole to find size.
2. Select Extra Large if the midpoint is about 45″ (approx. pant waist 40″–44″).
3. Place the tool bag on your dominant side and the fastener bag on the opposite side.
4. Buckle and adjust the 3″ Ranger Belt over typical work clothing for a secure fit.

Occidental Leather 5061 Features

• All-leather construction for daily jobsite durability
• 9 pockets and holders arranged for efficient fastener and tool access
• Left-side tape holster in place of an upper bag
• Holds angle square, cat’s paw, driver bits, and more
• Available in right-hand (5061) and left-hand (5061LH) layouts
• Made in the USA

Occidental Leather 5061 Applications

• Framing and rough carpentry layouts
• Finish carpentry fastener organization
• General carpentry and remodel tool storage

Occidental Leather 5061 Installation Overview

1. Select right-hand (5061) or left-hand (5061LH) orientation to match your setup.
2. Slide the pouch onto your work belt through the built-in leather tunnel.
3. Position on the left side for fastener access opposite your primary tool bag.
4. Load tape, fasteners, and layout tools into dedicated pockets.
5. Adjust belt position for comfortable reach before starting work.

Key Features

• All-leather, angled body for balanced, ergonomic access
• Fits most cordless drills
• Two dedicated drill/driver bit holders
• Premium full-grain leather construction
• Available in right- or left-hand orientations (5066 / 5066LH)
• Made in the USA

Applications

• Keep a cordless drill secured and accessible on your belt
• Hands-free carrying while climbing ladders or moving on site
• Carpentry, framing, electrical, and general construction tasks
• Quick access to driver bits during fastening work

Installation Overview

1. Slide holster onto a compatible work belt.
2. Position at preferred side for handed orientation.
3. Insert drill into angled pocket and secure with the strap if desired.
4. Store two bits in the integrated bit holders.

Occidental Leather 5017DB Features

• Classic 3-pouch leather tool bag with no tape pocket for a lighter setup
• Double outer bags plus dedicated holders for hammer, pencil, work knife, chisel, torpedo level, and lumber crayon
• Right-hand layout standard; also offered for left-hand builders as 5017DBLH
• Efficient organization with 10 pockets & tool holders
• Made in the USA

Occidental Leather 5017DB Applications

• Daily carry of core hand tools on the jobsite
• Framing, finish work, and general carpentry tool organization
• Right-side tool access for right-handed users; left-hand option for mirrored workflows
• Use with professional tool belts for quick access and productivity

Occidental Leather 5017DB Installation Overview

1. Select handedness (5017DB right-hand or 5017DBLH left-hand).
2. Slide or attach the bag to your work belt per belt slot/clip configuration.
3. Load core tools into dedicated holders and pouches.
4. Adjust position on belt for comfortable reach and balance.
5. Periodically clean and condition leather to maintain performance.

Key Features

• Extra heavy-duty bridle leather, custom tanned
• Edge stitched for strength and clean look
• Heavy-duty 1.75 in steel roller buckle, nickel finish
• Made in the USA

Applications

• Daily workwear belt for jobsite or shop
• Supports pants when carrying small holsters or accessories
• Durable casual belt for off-hours use

Installation Overview

1. Lay your current belt flat and measure from buckle end to your most-used hole.
2. Select the mid-range size closest to that measurement.
3. If no belt to measure, add 4 in to pant waist for approximate mid-range.
4. Choose size Small through XXX-Large based on chart below.

Occidental Leather 9540 Key Features

• Hand-specific tool holders for efficient workflow
• Two-ply, foam-core bags keep their shape when empty or loaded
• Abrasion-resistant industrial nylon construction
• Adjust-to-Fit design allows quick sizing changes for seasonal clothing
• D-rings pre-installed for use with suspension systems
• Left-handed model available as 9540LH
• Includes Oxy™ Tool Shields for sharp tool protection
• Made in USA

Occidental Leather 9540 Applications

• Finish carpentry — organized storage for precision tools
• Trim work — compact fastener capacity with speed square holster
• Light framing — balanced layout for everyday jobsite tasks
• Remodeling — lightweight rig for all-day wear
• General carpentry — hand-specific holders for common tools

Occidental Leather 9540 Installation Overview

1. Size the belt: Adjust the buckle to fit pant waist sizes 32"–41".
2. Position bags: Set fastener bag on left and tool bag on right for standard layout.
3. Attach hammer holder: Install the removable high-mount holder at center back.
4. Clip Tool Shields: Secure 2003 Oxy Tool Shields to bag edges or pocket as needed.
5. Connect suspenders if used: Clip to pre-installed D-rings.
6. Load tools and fasteners: Distribute weight evenly and confirm secure fit.

Occidental Leather 5018 Key Features

• Tool bag layout optimized for right-hand access
• Dedicated holders for pencils, knife, lumber crayon, chisel, torpedo level, and hammer
• Holster fits tape measures up to 35″
• Available in a left-hand version (5018DBLH)

Occidental Leather 5018 Applications

• Daily professional carpentry tool carry
• Framing and layout tasks
• Finish work and trim installation
• General construction tool organization

Occidental Leather 5018 Installation Overview

1. Slide the bag onto your work belt.
2. Position on the right side for dominant-hand access.
3. Load tools into designated pockets and holders.
4. Seat your tape measure in the holster.
5. Verify balance and adjust placement as needed.

Occidental Leather 2535 Features

• Freedom from tool clutter with 18 pockets & holders
• Ergonomically designed for even load distribution
• Can be worn with a tool belt; does not interfere with belts
• Fully adjustable straps for a custom fit
• Durable ballistic nylon with leather reinforcements
• One size fits most
• Made in the USA

Occidental Leather 2535 Applications

• General carpentry and framing tool organization
• Remodeling and punch-list work
• Electrical and low-voltage service calls
• Finish work where mobility and access are critical
• Jobsite tasks requiring hands-free fast access to tools

Occidental Leather 2535 Installation Overview

1. Loosen straps and put on the vest over work clothing.
2. Adjust shoulder and side straps until weight is balanced and secure.
3. Load tools into pockets and holders; place sharp tools in the included Pocket Shield.
4. Attach the clip-on hammer holder as needed.
5. Optionally wear with a tool belt; confirm vest does not impede belt movement.

Occidental Leather 5328 Features

• 10 oz Latigo belting leather for durability
• Heavy-duty spring steel belt clip for secure attachment
• Italian-style drop clasp for protected, quick access
• Fits iPhone 6 Plus, 7 Plus & similarly sized phones (verify dimensions)
• Clips to belts up to 2" wide
• Made in the USA

Occidental Leather 5328 Applications

• Hands-free phone carry on work belts
• Protection for larger smartphones on jobsites
• Daily use for tradespeople, contractors, and field techs

Occidental Leather 5328 Installation Overview

1. Clip the holster onto a belt up to 2" wide.
2. Insert phone into the pouch.
3. Close and secure the drop clasp.
4. Verify the clip is firmly attached before use.

Occidental Leather 5525 Key Features

• Round-bottom design adds structure and increases capacity
• 10 pockets & tool holders optimized for fasteners and layout tools
• Tape pocket holds tapes up to 35′
• Includes Oxy Tool Shield to protect sharp tools, bags, and body
• Right-hand layout; typically worn on the left side
• Made in the USA

Occidental Leather 5525 Applications

• Framing and general carpentry fastener carry
• Layout and measuring tools organization on the belt
• Jobsite tasks requiring frequent access to nails, screws, and bits
• Daily contractor use where durable leather storage is preferred

Occidental Leather 5525 Installation Overview

1. Thread the bag’s tunnel onto your work belt.
2. Position on the left side for right-handed use.
3. Load fasteners and layout tools into designated pockets/holders.
4. Place sharp tools in the included Oxy Tool Shield.
5. Check balance and adjust placement for comfortable reach.

Occidental Leather 8060 Key Features

• Lightweight OxyLights nylon construction for daily comfort
• 3-pouch layout: main, outer, and upper bags for organized access
• Tool-specific holders for blade square, angle square, cat’s paw, and driver bits
• Designed as a left-side fastener bag for framing and general carpentry
• Reinforced with leather at stress points for durability
• Made in the USA

Occidental Leather 8060 Applications

• Framing: Keep nails, layout tools, and bits organized
• General carpentry: Quick access to fasteners and small tools
• Jobsite setup: Left-hand fastener storage for balanced belt systems

Occidental Leather 8060 Installation Overview

1. Select handedness and position this fastener bag on the left side for right-handed setups.
2. Slide the bag onto a compatible work belt and secure in preferred position.
3. Load fasteners and layout tools into dedicated pockets/holders.
4. Verify balance and accessibility; adjust pouch position as needed.

Occidental Leather 5019 Key Features

• All-leather construction for durability and long service life
• Clean, open interior with no tool holders or dividers
• Compact size for carrying fasteners or small tools
• Lightweight at approximately 0.7 lb
• Belt-loop mount for easy placement on your work belt
• Made in the USA

Occidental Leather 5019 Applications

• Hold loose fasteners such as nails, screws, and anchors
• Carry small hand tools, bits, and accessories
• Add-on rear or side pouch to expand belt capacity
• Organize specialty hardware for trim, electrical, or punch-list work

Occidental Leather 5019 Installation Overview

1. Confirm your belt width and choose a mounting position.
2. Thread the work belt through the pouch’s loop.
3. Orient and center the pouch for comfortable reach.
4. Secure the belt and ensure the pouch hangs flat.
5. Load with fasteners or small tools and check balance.

Occidental Leather 6104 Features

• Streamlined 2-pouch layout for versatile carry
• No internal or external tool holders — ideal for fasteners and overflow
• Durable leather construction with riveted reinforcement
• Compact footprint to simplify belt organization
• Made in the USA

Occidental Leather 6104 Applications

• Carry nails, screws, and small hardware
• Add auxiliary storage to existing tool belts
• Create a lighter, minimalist belt setup
• Organize overflow fasteners on the jobsite

Occidental Leather 6104 Installation Overview

1. Thread the bag onto your work belt.
2. Place at your preferred reach point.
3. Load fasteners or tools into main and outer pouches.
4. Adjust position for balance and comfort.

Occidental Leather 8086 OxyLights Ultra Framer Features

• Designed with hand-specific tool holders
• Padded two-ply bags maintain structure
• Extremely abrasion-resistant industrial nylon
• Leather tool holders & corner reinforcement (NoSpill design)
• 7-pouch compact system with patented 2-in-1 outer pouch
• Available in left- or right-hand configurations (8086LH for lefties)
• Made in USA

Occidental Leather 8086 OxyLights Ultra Framer Applications

• Framing – carry nails, layout tools, and a hammer within reach
• Carpentry – organize hand tools, fasteners, and measuring gear
• Remodeling – lightweight setup for all-day wear
• Jobsite tool organization – keep essentials accessible and secure

Occidental Leather 8086 OxyLights Ultra Framer Installation Overview

1. Measure your current tool belt from buckle end to the hole you use.
2. Match that measurement to the size chart midpoint (SM–XXXL).
3. If no belt to measure, add 4″ to your pant waist for an approximate mid range.
4. Select left- or right-hand configuration as preferred.
5. Load tools and adjust belt to the midpoint hole for optimal fit.

Occidental Leather 9504 Features

• Cost-efficient fastener and tool management
• Versatile multi-pouch layout with holders for pencils, utility knife, and angle square
• Quick clip-on attachment to belts or waistbands up to 2" wide
• Lightweight, jobsite-tough nylon construction
• Made in the USA

Occidental Leather 9504 Applications

• Small tasks and punch-list work
• Trim and finish carpentry essentials
• Maintenance and repair duties
• Weekend DIY projects
• Service calls where minimal tools are needed

Occidental Leather 9504 Installation Overview

1. Attach: Clip the pouch to a belt or waistband up to 2" wide.
2. Load: Place fasteners and small tools into the main and outer bags.
3. Organize: Use dedicated holders for pencil, utility knife, and angle square.
4. Check: Ensure the clip is fully seated and the pouch is secure before use.
5. Remove: Unclip when finished and store in a dry place.

Occidental Leather 2575 Features

• Maximum comfort with ergonomic, even load distribution
• Freedom of movement with wide-shoulder, open-back design
• Functional organization with 28 pockets and holders
• Nylon-reinforced stress points, edges, and pockets for durability
• Includes two Oxy Tool Shields for knives, chisels, pliers, etc.
• One size fits most; left-handed option available as 2575LH

Occidental Leather 2575 Applications

• General carpentry and framing
• Remodeling and finish work
• Electrical, HVAC, and service trades
• Jobsite organization without a traditional belt

Occidental Leather 2575 Installation Overview

1. Adjust vest straps for a balanced, comfortable fit.
2. Attach Oxy Tool Shields where desired for sharp tool protection.
3. Load tools into designated pockets for fast access.
4. Re-check balance and fine-tune straps to evenly distribute weight.