Occidental Leather Professional Tool Bags

Occidental Leather 9511 Key Features

• Cost efficient fastener management
• Modular clip-on design for easy swap between tasks
• Slightly deeper and narrower than the 9501
• Clips to belts up to 2 in wide; also clips to toolboxes or truck interiors
• Made in USA

Occidental Leather 9511 Applications

• Carrying nails, screws, and small fasteners
• Modular add-on storage for tool belts
• Quick-change setups for varied tasks
• Clipping to a truck or toolbox for organized access

Occidental Leather 9511 Installation Overview

1. Verify your belt is no wider than 2 in.
2. Slide the clip over the belt edge until fully seated.
3. Load fasteners into the pouch.
4. Adjust position on belt for comfort and reach.
5. Remove and reclip as needed for different applications.

Occidental Leather B5057 Features

• Compact 4 pocket organizer protects you, your tools, and your clothes
• Creates an instant mini tool carrier for pliers, screwdrivers, and more
• Snap loop attaches to belts up to 2 inches wide
• Durable leather construction for daily use
• Made in USA

Occidental Leather B5057 Applications

• Small repair jobs
• Shop and maintenance work
• Gardening and yard upkeep
• Cabinetmaking and finish tasks
• Farm and field repairs

Occidental Leather B5057 Installation Overview

1. Load tools into the four pockets to suit your task.
2. Place the caddy in your pant pocket or position at the belt line.
3. Wrap the snap loop around a belt up to 2 inches wide, if preferred, and close the snap.
4. Adjust tool placement for balance and quick access.
5. After use, remove debris and store dry.

Occidental Leather 8068 Features

• Two-compartment main bag with drill/screw gun holster
• Patented 2 in 1 outer pouch adds storage without bulk
• Right-side layout; square edge to the rear
• Holders for driver bits and pencil
• Leather sleeve for Clip-On accessories
• Rafter square slot behind outer pouch
• Pocket and tool holders: 9
• Weight: 1.25 lbs
• Made in the USA

Occidental Leather 8068 Applications

• Metal framing and stud work tool carry
• Organizing drill, bits, and quick-release clamps
• Keeping rafter square accessible on belt
• Right-side belt-mounted storage for cordless tools

Occidental Leather 8068 Installation Overview

1. Slide bag onto a work belt up to 3 in wide.
2. Position on the right side with square edge to rear.
3. Seat drill or screw gun in the holster.
4. Load bits, pencil, and clamps into designated pockets.
5. Place rafter square in the rear slot and check balance.

Occidental Leather B8017DBLH Key Features

• Left handed layout worn on the left side for quick access
• Holders for pencils, work knife, chisel, level, and lumber crayon
• Heavy duty hammer loop for secure carry
• OxyRed leather reinforced corners and internal holders for durability
• Lightweight OxyLights hybrid nylon and leather construction
• Three pouch design for compact organization
• Made in USA

Occidental Leather B8017DBLH Applications

• Organizing everyday carpenter and framer hand tools
• Left side carry on work belts and belt systems
• Keeping pencils, knives, chisels, and levels at the ready
• Jobsite use where lightweight yet durable storage is needed
• General construction and finishing tasks

Occidental Leather B8017DBLH Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the left side for left handed access.
3. Secure the belt and adjust placement for comfort.
4. Load tools into dedicated holders and pouches.
5. Confirm hammer loop and tools are seated securely before use.

Occidental Leather 8584 Key Features

• 10 in deep main pouch with structured FatLip leather mouth
• Full leather boot for rugged longevity
• 13 pockets and tool holders for everyday layout tools
• Right-side layout; left-hand version available as 8584LH
• Made in the USA

Occidental Leather 8584 Applications

• Organizing and carrying hand tools on a tool belt
• Framing and general carpentry tasks
• Remodeling and jobsite maintenance work
• Right-hand dominant tool layouts

Occidental Leather 8584 Installation Overview

1. Slide the bag onto a compatible work belt through the leather belt slot.
2. Position on the right side for right-hand use (or choose 8584LH for left-hand use).
3. Load tools by category into interior and exterior holders.
4. Secure any clips or add-on holders as needed and check balance.

Occidental Leather B5612 Features

• Light-weight, classic black all leather construction
• External leather hammer holder and double outer bags
• Internal pockets for level, chisel, drill bits, knife, pencils, and lumber crayon
• Reinforced back wall at stress points for durability
• Right-side wear layout; left-hand version available as B5612LH
• Made in USA

Occidental Leather B5612 Applications

• Organizing hand tools for carpentry and framing
• Quick-access storage for chisels, knives, pencils, and bits
• Carrying levels and small measuring tools
• General construction and remodel tool carry

Occidental Leather B5612 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the right side for right-hand access.
3. Load tools into main and outer pockets; place sharp tools in the Oxy Tool Shield.
4. Adjust placement for comfort and balanced weight.

Occidental Leather B8017DB Key Features

• 3-pouch layout for compact organization
• Dedicated tool holders for chisel, knife, level, pencils, and lumber crayon
• Heavy-duty hammer loop for secure carry
• Main bag corners reinforced with OxyRed leather
• Right-hand layout; left-hand model available

Occidental Leather B8017DB Applications

• Daily carry and organization of essential hand tools
• Carpentry and framing tasks needing quick tool access
• Finish work where compact, lightweight storage is preferred
• Jobsite use with a compatible work belt

Occidental Leather B8017DB Installation Overview

1. Attach the tool bag to a compatible work belt.
2. Position on the right side for right-hand layout.
3. Load tools into dedicated holders and pouches.
4. Check rivets and stitching; ensure secure fit before use.

Occidental Leather 9521LH Key Features

• Compact finisher layout ideal for trim, light framing and finish work
• Round bottom, full capacity main and outer bags with two ply foam core retain shape
• Clip on leather tab for tape; driver bit and nail set pouches included
• Metal hammer holder
• Left handed configuration worn on left side for fast tool access

Occidental Leather 9521LH Applications

• Trim carpentry organization
• Light framing tool carry
• Finish carpentry and punch list work

Occidental Leather 9521LH Installation Overview

1. Position on your work belt at the left hip for left handed access.
2. Secure the bag onto the belt and load tools into the dedicated pockets.
3. Attach the included Oxy Tool Shield where needed for sharp tool protection.

Occidental Leather 8585XL Key Features

• Hand specific tool holders for efficient layout
• Padded two ply tool bags hold their shape
• Industrial nylon is highly abrasion resistant
• Leather tool holders with leather reinforced corners
• Available left handed as model 8585LH

Occidental Leather 8585XL Applications

• Carpentry and framing setups
• General construction tool carry
• Remodeling and jobsite installation work

Occidental Leather 8585XL Installation Overview

1. Lay your current belt flat; measure from buckle end to most used hole.
2. Select the Extra Large size closest to that mid range measurement.
3. Position bags and holders to preferred left or right layout.
4. Secure buckle and adjust for a snug, supportive fit.

Key Features

• Popular 3 pouch pro layout without a tape pocket
• Double outer bags for added capacity and organization
• Tool holders for pencils, utility knife, lumber crayon, chisel, torpedo level, and hammer
• Left handed configuration; worn on the left side
• Made in the USA

Applications

• Carpentry and framing tool organization
• General construction and remodeling
• Finish work tool carry
• Jobsite hand tool access and storage

Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the left side for left handed access.
3. Load tools into dedicated holders and pouches.
4. Check balance and tighten belt for a secure fit.

Occidental Leather 8017 Features

• Streamlined 2-pouch layout for focused setups
• Right-side wear for tools accessed with the right hand
• 9 total pockets and holders for common hand tools
• Tape pocket removed for a lighter profile
• Made in USA

Occidental Leather 8017 Applications

• Daily carry of layout and framing essentials
• Organizing chisels, knives, pencils, and level on the job
• Right-side tool access for carpentry and trim work

Occidental Leather 5191XL Key Features

• Unique one-piece tool belt assembly for balanced load distribution
• Premium top-grain leather construction
• Hand-specific tool holders for efficient workflow
• Copper-riveted main bags for durability
• NoSpill tool holder system keeps tools secure
• Sheepskin-lined interior for comfort
• Made in USA
• Not available as left-hand model; suggested 9550LH

Occidental Leather 5191XL Applications

• Framing and general carpentry
• Remodeling and residential construction
• Jobsite tool organization and carry
• Finish carpentry tool layout

Occidental Leather 5191XL Installation Overview

1. Put the belt on over typical work clothing and note the hole used.
2. Remove the belt and measure from the buckle end to that hole to confirm size.
3. Adjust fit using midpoint hole; 4 inches of adjustment each way.
4. Load tools into hand-specific holders; secure sharp tools in dedicated holsters.
5. Verify balanced weight before use.

Occidental Leather B8064LH Key Features

• Patented 2-in-1 outer pouch with built-in angle square holster
• Four-bag layout: main, outer, upper, and 2-in-1 pouch
• Dedicated holders for tri-square, cat's paw, nail sets, and driver bits
• Left-handed configuration; worn on right side
• Industrial nylon with leather reinforcements; Made in USA

Occidental Leather B8064LH Applications

• Framing and general carpentry fastener storage
• Organizing layout tools such as angle and tri-squares
• Jobsite carry for nail sets, driver bits, and pry tools
• Left-handed belt setups worn on the right hip

Occidental Leather B8064LH Installation Overview

1. Orient the pouch for right-side wear for left-handed users.
2. Thread onto your work belt and position for comfortable reach.
3. Secure adjacent holders as needed and load tools by category.
4. Confirm clear access to the 2-in-1 outer pouch and square holster.

Occidental Leather 8551 Features

• 2 inch steel clip enables fast on and off attachment
• Drawstring closure secures fasteners and small tools
• Dual layer 1000D sides and 1050D bottom for wear resistance
• Clips to most belts or waistbands up to 2 inches wide
• Made in the USA

Occidental Leather 8551 Applications

• Carry nails, screws, and small parts on the job
• Quick access storage for trim shims and wedges
• Add on pouch for tool belts and work vests
• Lightweight parts holder for service and install work

Occidental Leather 8551 Installation Overview

1. Slide or clip the pouch onto a belt or waistband up to 2 inches wide.
2. Load with fasteners or small tools.
3. Pull the drawstring to secure contents as needed.
4. Release the clip to remove when finished.

Occidental Leather 8552 Key Features

• 2 inch belt clip for fast on off attachment
• Drawstring closure keeps contents secure yet accessible
• Dual layer 1000D nylon sides and 1050D nylon bottom for wear resistance
• Medium size: 6 in diameter x 7 in high
• Made in the USA

Occidental Leather 8552 Applications

• Carry fasteners, anchors, and small hardware
• Quick access storage for bits and small hand tools
• Add on pouch for tool belts and vests
• Jobsite organization for installers and carpenters

Occidental Leather 8552 Installation Overview

1. Slide the 2 inch clip over your belt, pocket, or strap.
2. Load hardware or tools into the pouch.
3. Cinch the drawstring to secure contents.
4. Release the clip to reposition or remove as needed.

Occidental Leather 8585LHM Key Features

• Left-handed layout
• Leather FatLip bag mouth for structure and abrasion resistance
• Full leather boot with 10 in deep industrial nylon bags
• Hand-specific tool holders and padded two ply construction
• 25 pockets and holders; Made in USA

Occidental Leather 8585LHM Applications

• Framing and rough carpentry
• General construction and remodeling
• Finish and trim tasks requiring organized fasteners and tools
• Jobsite setups needing left-handed tool access

Occidental Leather 8585LHM Installation Overview

1. Measure an existing belt to confirm medium belt size.
2. Position the belt over work clothing and adjust for comfort.
3. Arrange tool and fastener bags on the left-handed layout.
4. Secure the hammer holder and clip-on accessories.
5. Load tools and verify balanced weight and access.

Occidental Leather 8564 Key Features

• 9 pockets and tool holders for fasteners and small tools
• Patented 2-in-1 outer bag with angle square holster; 3 bags total
• Durable nylon body with OxyRed leather-reinforced corners
• Clip-on design fits the 2535 Builders Vest
• Made in USA

Occidental Leather 8564 Applications

• Organizing nails, screws, and driver bits
• Carrying angle and tri-squares
• Stowing a cats paw or similar pry tool
• Left-side fastener access on Builders Vest systems

Occidental Leather 8564 Installation Overview

1. Align the clip-on tabs with the attachment points on the 2535 Builders Vest.
2. Securely clip the pouch to the vest until it locks in place.
3. Verify the pouch is seated and does not shift.
4. Load tools and fasteners; place frequently used items for left-hand access.

Occidental Leather 8585M Key Features

• Hand specific tool holders for efficient layout
• Padded two ply bags hold shape under load
• Industrial nylon with leather holders and reinforced corners
• Leather FatLip mouth keeps the bag formed and protected
• Full leather boot for rugged wear
• Left handed version available as 8585LH
• Made in USA

Occidental Leather 8585M Applications

• Carpentry and framing tool organization
• Jobsite fastener and small parts carry
• Daily use for production builders
• General construction tool storage
• Remodeling and trim work setups

Occidental Leather 8585M Installation Overview

1. Lay your current belt flat and measure from buckle end to your most used hole.
2. Select Medium if the mid range near 37 in. matches your measurement.
3. Adjust using the 9 holes to fine tune fit across 4 in. of range each way.
4. Attach bags and hammer holder to preferred positions.
5. Load tools and confirm balance and comfort before use.

Occidental Leather B8554 Features

• 2 inch belt clip for quick attachment and removal
• Drawstring closure helps retain contents
• Durable build with dual layer 1000D nylon sides and 1050D nylon bottom
• Tall size: 5 in diameter x 8.5 in high
• Made in the USA

Occidental Leather B8554 Applications

• Holding fasteners, shims, and small hand tools
• Clip on storage for belts and vests
• Jobsite organization and quick access

Occidental Leather B8554 Installation Overview

1. Slide or clip the 2 inch belt clip onto your belt or strap.
2. Load tools or fasteners into the pouch.
3. Cinch the drawstring to secure contents.
4. Release clip to reposition or remove as needed.

Occidental Leather 8583LH Features

• 10 inch deep main bag with full leather boot
• Leather FatLip mouth keeps bag formed, open, and abrasion resistant
• Patented 2 in 1 outer bag with built in angle square holster
• Tri square sleeve, cats paw loop, and external pouches for nail sets or driver bits
• Left handed layout worn on the right side
• Made in USA

Occidental Leather 8583LH Applications

• Framing and carpentry fastener organization
• Drywall installation tool and bit storage
• General construction fastener and small tool management

Occidental Leather 8583LH Installation Overview

1. Slide the bag onto your work belt.
2. Position on the right side for left handed use.
3. Load fasteners and tools into designated pockets.
4. Confirm the FatLip mouth and compartments are clear for access.

Occidental Leather 8585 XXXL Key Features

• 25 pockets and tool holders for organized storage
• Hand-specific tool holder layout
• Padded two-ply bags maintain structure
• Industrial nylon for high abrasion resistance
• Leather tool holders with reinforced corners
• Full leather boot and FatLip bag mouth
• Made in USA

Occidental Leather 8585 XXXL Applications

• Production carpentry and framing
• General construction tool organization
• Remodeling and installation tasks
• Finish and trim carpentry
• Jobsite tool carry with quick access

Occidental Leather 8585 XXXL Installation Overview

1. Measure from belt buckle to the hole you use to determine belt size.
2. Wear over normal work clothes and select the best buckle hole.
3. Attach tool and fastener bags to preferred sides.
4. Secure the 2-in-1 holder at the rear for hammer or specialty tools.
5. Load tools and adjust for comfort and balance.

Occidental Leather 8087 M Key Features

• 20 pockets and tool holders
• Hand-specific tool organization
• Padded two-ply bags maintain structure
• Abrasion-resistant industrial nylon with leather reinforcement
• Made in USA

Occidental Leather 8087 M Applications

• Metal framing and stud work
• Finish carpentry tasks
• Remodeling and general construction
• Organizing fasteners, layout tools, and clamps
• Holstering impact drivers or screw guns

Occidental Leather 8087 M Installation Overview

1. Measure and select the correct belt size; fasten at midpoint hole.
2. Attach included bags and holders to the 3" Ranger belt.
3. Adjust belt fit for comfort and balance.
4. Load tools and fasteners; place driver in the gun holster.
5. Verify secure attachment points and even weight distribution.

Key Features

• 20 pockets and tool holders
• Hand specific tool organization
• Padded two ply bags hold their shape under load
• Industrial nylon with leather tool holders and corner reinforcement
• Right side gun holster for impact or screw guns
• Made in USA

Applications

• Metal stud framing and fastening
• Finish carpentry and trim installation
• Remodeling and punch list tasks
• General layout and fastening work

Installation Overview

1. Measure and select the correct belt size for over garment wear.
2. Thread the work belt through the bags and holders in preferred positions.
3. Secure the hammer holder and accessories to the belt.
4. Adjust the belt for a snug, balanced fit at the midpoint hole.
5. Load tools and fasteners; verify balanced weight and accessibility.

Occidental Leather B5060LH Key Features

• Left-handed layout worn on the right side for quick access
• Three stacked pouches with top-access tier
• 9 pockets and tool holders for common layout tools
• Premium leather construction for long-term durability
• Made in the USA

Occidental Leather B5060LH Applications

• Framing and rough carpentry fastener storage
• General carpentry and remodel tasks
• Organizing layout squares, bits, and small tools

Occidental Leather B5060LH Installation Overview

1. Slide the bag onto your work belt.
2. Position on the right side to suit left-handed setups.
3. Load fasteners and layout tools into the designated pockets.
4. Check balance and adjust position for comfort.