Holiday Gift Guide 2021

Occidental Leather 5008SM Key Features

• Extra heavy-duty bridle leather, custom tanned in the USA
• Edge-stitched for quality, appearance & strength
• Heavy-duty steel roller buckle with nickel finish
• 1.5" belt width for everyday wear & tool carry
• Made in the USA

Occidental Leather 5008SM Applications

• Daily workwear belt for tradespeople
• Supports clip-on tool pouches & holsters
• General-duty pant belt for jobsite use
• Casual wear where rugged durability is preferred

Occidental Leather 5008SM Installation Overview

1. Lay an existing belt flat; measure from buckle end to most-used hole.
2. Choose the size closest to that measurement’s mid-range.
3. If no belt to measure, add 4" to pant waist for an approximate mid-range.
4. Fasten the buckle and test fit; adjust using the belt holes as needed.

Occidental Leather 8567 Key Features

• Fits 3" belts for stable, belt-worn carry
• Compatible with Bosch PS20-02, 3318-2G, 33614-26, 23612 Impactor; Hitachi WH12DAF2; Makita 18V LXT Impact Drivers, BTD 142HW, and 18V drills; Milwaukee 18V Lithium BDT 140, LXT 18V drills
• Hybrid build — durable nylon body reinforced with leather
• 4 pockets/tool holders for drill, bits, fasteners, and small tools
• Lightweight design at 0.5 lbs
• Slides easily onto most standard tool belts
• Made in the USA

Occidental Leather 8567 Applications

• Framing and general construction
• Punch-out and finish work
• Electrical & service technician tasks
• Remodeling and jobsite tool organization

Occidental Leather 8567 Installation Overview

1. Slide the holster onto your tool belt (fits 3" belts).
2. Insert the drill/driver into the main pocket.
3. Secure using the snap strap.
4. Load bits and small tools into the front holders.
5. Confirm a snug fit before working.

Key Features

• Belt-worn holster accepts nail strips up to 16D
• Heavy belting leather construction for durability
• Holds up to 8 racks for fewer reloads
• Loops onto belts up to 3″ wide
• Made in the USA

Applications

• Carry and organize nail strips for framing nailers
• Speed up reloads while keeping nails within reach
• Reduce pocket clutter and protect nail strips on the belt

Installation Overview

1. Thread the holster onto a work belt up to 3″ wide.
2. Insert nail strips (up to 16D) into the pouch.
3. Position for preferred hand access and begin use.

Occidental Leather 5019 Key Features

• All-leather construction for durability and long service life
• Clean, open interior with no tool holders or dividers
• Compact size for carrying fasteners or small tools
• Lightweight at approximately 0.7 lb
• Belt-loop mount for easy placement on your work belt
• Made in the USA

Occidental Leather 5019 Applications

• Hold loose fasteners such as nails, screws, and anchors
• Carry small hand tools, bits, and accessories
• Add-on rear or side pouch to expand belt capacity
• Organize specialty hardware for trim, electrical, or punch-list work

Occidental Leather 5019 Installation Overview

1. Confirm your belt width and choose a mounting position.
2. Thread the work belt through the pouch’s loop.
3. Orient and center the pouch for comfortable reach.
4. Secure the belt and ensure the pouch hangs flat.
5. Load with fasteners or small tools and check balance.

Occidental Leather 9504 Features

• Cost-efficient fastener and tool management
• Versatile multi-pouch layout with holders for pencils, utility knife, and angle square
• Quick clip-on attachment to belts or waistbands up to 2" wide
• Lightweight, jobsite-tough nylon construction
• Made in the USA

Occidental Leather 9504 Applications

• Small tasks and punch-list work
• Trim and finish carpentry essentials
• Maintenance and repair duties
• Weekend DIY projects
• Service calls where minimal tools are needed

Occidental Leather 9504 Installation Overview

1. Attach: Clip the pouch to a belt or waistband up to 2" wide.
2. Load: Place fasteners and small tools into the main and outer bags.
3. Organize: Use dedicated holders for pencil, utility knife, and angle square.
4. Check: Ensure the clip is fully seated and the pouch is secure before use.
5. Remove: Unclip when finished and store in a dry place.

Occidental Leather 9025 Key Features

• Compact multifunction design with 6 pockets & holders
• Large-volume padded nylon fastener bag for small parts
• Includes Oxy Tool Shield for safe storage of sharp tools
• Tape holder and hammer loop for core tools
• Slides onto belts up to 3" wide
• Made in the USA

Occidental Leather 9025 Applications

• Trim and finish work where minimal gear is preferred
• Service calls and punch-list tasks
• Grab-and-go setups or secondary pouch use
• Carrying tape, hammer, blade/chisel, pencils, and fasteners

Occidental Leather 9025 Installation Overview

1. Slide the pouch onto a work belt up to 3" wide.
2. Insert the Oxy Tool Shield if using sharp tools.
3. Load tape, hammer, pencils, and fasteners into designated holders.
4. Verify secure fit on belt and balanced tool placement.

Occidental Leather 5520 Key Features

• 5-in-1 capacity — holders for hammer, pliers, pencil, lumber crayon/screwdriver, and sharp tools
• Includes removable Oxy Tool Shield for chisels, knives, or similar
• Premium full-grain American leather construction
• Compact footprint saves belt space; fits belts up to 3" wide
• Made in the USA

Occidental Leather 5520 Applications

• Framing: Keep core hand tools at the ready
• Electrical work: Organize pliers, drivers, and markers
• Carpentry: Carry chisels, hammers, and layout tools
• Punch-list/finish tasks: Streamlined, compact tool access

Occidental Leather 5520 Installation Overview

1. Slide the holder onto a work belt up to 3" wide.
2. Insert the removable Oxy Tool Shield into its pocket if using sharp tools.
3. Load tools into the designated holders (hammer, pliers, pencil, crayon/screwdriver).
4. Check retention and accessibility; adjust tool placement as needed.

Occidental Leather 5328 Features

• 10 oz Latigo belting leather for durability
• Heavy-duty spring steel belt clip for secure attachment
• Italian-style drop clasp for protected, quick access
• Fits iPhone 6 Plus, 7 Plus & similarly sized phones (verify dimensions)
• Clips to belts up to 2" wide
• Made in the USA

Occidental Leather 5328 Applications

• Hands-free phone carry on work belts
• Protection for larger smartphones on jobsites
• Daily use for tradespeople, contractors, and field techs

Occidental Leather 5328 Installation Overview

1. Clip the holster onto a belt up to 2" wide.
2. Insert phone into the pouch.
3. Close and secure the drop clasp.
4. Verify the clip is firmly attached before use.

Occidental Leather B5114K Key Features

• Handcrafted premium leather construction
• Low-profile carry keeps cat’s paw snug to the body
• DIY installation kit with copper rivets and instructions
• Mounts to existing pouches, vests, or tool rigs
• Made in USA

Occidental Leather B5114K Applications

• Framing and general carpentry
• Roofing where secure tool retention is needed
• Finish carpentry and high-mobility tasks
• Organized carry for cat’s paw/pry bar on tool belts or vests

Occidental Leather B5114K Installation Overview

1. Prepare tools: smooth face hammer, side/flush cutters, 9/32 deep socket, pick, drill with 3/16 bit, and a hard surface/anvil.
2. Drill out the two outer rivets from the non-dominant side bag to remove the flared ends.
3. Insert a rivet through the hanger front and through the sleeve’s hole.
4. Set the washer tight using a hammer and socket or small pipe.
5. Trim rivet length, leaving about 1/8"–3/16".
6. Peen the rivet on a hard surface with a smooth face hammer to finish.

Occidental Leather 5114K Features

• Low-profile carry keeps cat’s paw tight to body
• Premium, handcrafted leather construction
• DIY install with copper rivets and step-by-step guide
• Made in USA

Occidental Leather 5114K Applications

• Framing: Secure access to pry bar while moving on site
• Roofing: Reduces swing and bulk during high-mobility tasks
• Carpentry: Keeps cat’s paw organized and within reach
• Finish work: Streamlined holder for tight workspaces

Occidental Leather 5114K Installation Overview

1. Gather tools: smooth-face hammer, side cutters, 9/32 deep socket, pick, drill with 3/16 bit, and an anvil or hard surface.
2. Drill out the two outer rivets on the non-dominant side bag to remove flared sections.
3. Align sleeve and push new rivet through hanger and sleeve holes.
4. Seat washer tight using hammer and socket or small pipe.
5. Trim rivet length to about 1/8"–3/16".
6. Peen rivet on a hard surface with a smooth-face hammer to finish.

Key Features

• 4-in-1 functionality — holds tape, pencil, lumber crayon or screwdriver, plus sharp tools
• Includes Oxy Tool Shield for safe storage of chisels, knives, and cutters
• Premium full-grain leather for durability and long service life
• Belt-ready tunnel loop fits belts up to 3" wide
• Compact design provides 4x capacity in the space of one holder
• Made in USA

Applications

• Carry and organize tape measure, marking tools, and a utility knife on the belt
• Framing, finish work, and general carpentry where quick tool access is needed
• DIY and weekend projects requiring compact tool storage

Installation Overview

1. Verify belt width (up to 3").
2. Thread the belt through the holder’s tunnel loop.
3. Position the holder at your preferred location on the belt.
4. Load tape, pencil, crayon/screwdriver, and place sharp tools in the Oxy Tool Shield.
5. Check that tools are seated securely before use.

Occidental Leather 5523 Key Features

• 4-in-1 capacity for tape, pencil, crayon/screwdriver, and sharp tools
• Includes Oxy Tool Shield for chisels, knives, or cutters
• Extra heavy-duty steel clip fits belts up to 2" wide
• Sturdy American leather construction for long-term durability
• Clip-on design for quick attachment and removal
• Made in the USA

Occidental Leather 5523 Applications

• Carry and access a tape measure on the job
• Keep pencils and lumber crayons within easy reach
• Holster a screwdriver or similar hand tool
• Safely store sharp tools using the included shield
• Clip to work belts for carpentry, framing, or finish work

Occidental Leather 5523 Installation Overview

1. Attach the steel clip to a belt up to 2" wide.
2. Insert tape measure into the main pocket.
3. Place pencil and crayon/screwdriver in side holders.
4. Mount sharp tools in the Oxy Tool Shield.
5. Confirm secure fit before use.

Occidental Leather 8578 Key Features

• Clip-on mount with spring steel clip for chest attachment to Stronghold suspenders
• Padded smartphone sleeve with velcro flap for secure carry
• Organizers for pencils, notepad, and driver bits
• Seven total pockets/tool holders
• Easy to install and remove
• Made in the USA

Occidental Leather 8578 Applications

• Chest-mounted storage on Stronghold suspenders
• Quick access to phone, pencils, notepad, and driver bits
• Staying organized while climbing ladders or moving on the jobsite
• Lightweight carry for everyday trade essentials

Occidental Leather 8578 Installation Overview

1. Position the spring steel clip over the chest strap of Stronghold suspenders.
2. Press to fully seat the clip until the pocket is secure.
3. Load tools, phone, and accessories into the designated sleeves.
4. Close the phone flap and check retention before use.
5. Remove by lifting the clip when you need to reposition or store.

Occidental Leather 8552 Features

• 2 in. steel clip for quick on/off belt or waistband attachment
• Drawstring closure keeps fasteners and parts contained
• Durable dual-layer nylon: 1000D sides with 1050D bottom
• Medium size capacity: 6 in. diameter x 7 in. high
• Proudly made in the USA

Occidental Leather 8552 Applications

• Holding screws, nails, and small fasteners
• Storing small tools or parts for carpentry and framing
• Clip-on pouch for light, on-the-go organization
• Supplemental storage on tool belts or work vests

Occidental Leather 8552 Installation Overview

1. Attach the steel clip to a belt or waistband up to 2 in. wide.
2. Load fasteners or small tools into the pouch.
3. Pull the drawstring to secure contents as needed.
4. Release the clip to remove the pouch when finished.

Occidental Leather 8554 Features

• 2 in. steel clip for secure belt or waistband attachment
• Drawstring closure keeps fasteners and small tools contained
• Dual-layer build: 1000D nylon sides with 1050D nylon bottom for high abrasion resistance
• Tall capacity: 5 in. diameter x 8.5 in. high
• Clips to most belts up to 2 in. wide
• Made in the USA

Occidental Leather 8554 Applications

• Carry fasteners such as screws, nails, and hardware
• Quick-access storage for small hand tools and bits
• Materials handling on trim, framing, or service tasks
• Supplemental clip-on pouch for tool belts or work pants

Occidental Leather 8554 Installation Overview

1. Slide the steel clip over a belt or waistband up to 2 in. wide.
2. Load fasteners or small tools into the pouch.
3. Cinch the drawstring to secure contents.
4. Position for comfortable reach; adjust as needed.
5. Release the clip to remove the pouch when finished.

Occidental Leather B8552 Key Features

• 2" steel clip for quick belt or waistband attachment
• Drawstring closure keeps contents secure
• Dual-layer construction: 1000D nylon sides, 1050D nylon bottom
• Medium size capacity: 6" diameter x 7" high
• Clips to most belts up to 2" wide
• Made in the USA

Occidental Leather B8552 Applications

• Carry and secure fasteners, screws, and nails
• Keep small hand tools within reach on the belt
• Trim and finish work where quick access is essential
• Service and punch list tasks requiring light, mobile storage
• Supplemental pouch for tool belts and work vests

Occidental Leather B8552 Installation Overview

1. Attach the 2" steel clip to a compatible belt or waistband (up to 2" wide).
2. Load fasteners or small tools into the pouch.
3. Cinch the drawstring to secure contents.
4. Position the pouch for easy access and adjust as needed.
5. Release the drawstring and unclip to remove when finished.

Occidental Leather 9020B Key Features

• Extra heavy 2" wide straps for reliable support
• Front and rear adjustability; non-stretch webbing
• Harness leather rear spreader for durability
• Quality super-heavy clamps attach securely
• Designed to support pants or tool belts
• Made in the USA

Occidental Leather 9020B Applications

• Supporting tool belts to reduce hip and back strain
• Holding up work pants securely on the jobsite
• Carpentry, electrical, framing, and general construction
• Daily use with leather or nylon work belts

Occidental Leather 9020B Installation Overview

1. Attach front clamps to your belt or waistband at even spacing.
2. Center the rear leather spreader and clamp to the back of the belt/waistband.
3. Adjust front and rear strap lengths for a balanced, comfortable fit.
4. Check clamp grip and re-tighten after loading your tool belt.

Key Features

• Compact 4-pocket layout organizes small hand tools
• Fits in most pants pockets; protects tools and clothing
• Snap loop attaches to belts up to 2″ wide
• Durable leather construction for everyday use
• Great for small repairs, shop work, gardening, cabinetmaking, and farm maintenance

Applications

• Small repair and maintenance tasks
• Shop and bench work tool organization
• Gardening and outdoor upkeep
• Cabinetmaking and finish work
• Farm and field repairs

Installation Overview

1. Load the pockets with frequently used small tools.
2. Place the caddy in your pants pocket for quick access, or
3. Use the snap loop to secure the caddy to a belt up to 2″ wide.
4. Adjust tool placement for balance and comfort.

Occidental Leather 5057 Features

• Compact 4-pocket organizer keeps hand tools separated
• Fits in most pockets or snaps to belts for quick access
• Durable leather construction with reinforced stitching
• Lightweight for all-day carry
• Made in USA

Occidental Leather 5057 Applications

• Small repair tasks and service calls
• Shop and bench work tool organization
• Gardening and outdoor upkeep
• Cabinetmaking and woodworking
• Farm maintenance and general DIY

Occidental Leather 5057 Installation Overview

1. Load the caddy with frequently used tools.
2. Place the caddy in a pants pocket or use the snap loop.
3. Snap the loop over a work belt up to 2.5" wide if preferred.
4. Arrange tools across the 4 pockets for balance and access.
5. Verify secure carry before starting work.

Occidental Leather 5527 Features

• Designed for offset metal snips (Wiss M6/M7) & pruning shears
• Full-grain American leather construction for durability
• Works with belts up to 3″ wide for stable carry
• Compatible with Oxy™ Tool Shield for added protection
• Made in the USA

Occidental Leather 5527 Applications

• Steel framing and sheet metal work
• General contracting and remodeling
• Landscaping and pruning tasks
• DIY projects requiring frequent snip use

Occidental Leather 5527 Installation Overview

1. Slide holster onto a work belt up to 3″ wide.
2. Seat the holster in your preferred position for easy reach.
3. Insert offset snips or pruning shears into the pouch.
4. Optionally add an Oxy™ Tool Shield for extra liner protection.

Occidental Leather 5047 Features

• All-in-one layout holds a utility knife, 2 pencils, and a tape measure
• Works great as a chalk line holster
• Slim, lightweight profile for tight spaces and finish tasks
• Durable, high-quality leather construction
• Made in the USA
• Fit tip: removing the tape clip may improve seating; leather breaks in over time

Occidental Leather 5047 Applications

• Finish carpentry and punch-list work
• Quick tasks needing only essential tools
• Organizing a tape, knife, pencils, and chalk line on a belt

Occidental Leather 5047 Installation Overview

1. Thread your work belt through the holster slots and secure it.
2. Load the tape measure, utility knife, and pencils into their pockets.
3. Allow time for leather break-in; remove the tape clip if needed for a better fit.

Occidental Leather 9512 Key Features

• Tool-specific storage for tape, spiral pad, pens, pencils, screwdriver, utility knife & pliers
• Industrial 2-ply Cordura® with foam core for structure and durability
• Compact footprint ideal for light-duty tasks, inspections, and service work
• Accepts work belts up to 2″ wide for a secure fit
• Made in the USA

Occidental Leather 9512 Applications

• Punch list work where minimal tools are needed
• Service calls and field repairs
• Inspections and walkthroughs
• Light-duty maintenance tasks
• Everyday carry for essential hand tools

Occidental Leather 9512 Installation Overview

1. Slide the pouch onto a work belt up to 2″ wide.
2. Organize essential tools in the designated pockets.
3. Securely seat heavier items like a tape measure in the main compartment.
4. Verify comfortable positioning on belt before use.
5. Remove debris periodically to maintain smooth access.

Key Features

• Optional strap for Journeyman’s Tote and compatible carry bags
• Hand crafted from durable bridle leather
• Adjustable shoulder pad for added comfort
• High–quality nickel–plated swivel steel clips for easy on/off
• 1″ wide strap adjusts 45″ – 57.5″
• Detaches in seconds for storage in your gear
• Made in the USA

Applications

• Shoulder carry upgrade for totes and tool bags
• Travel and everyday carry where a durable strap is needed
• Replacement strap for compatible Occidental Leather bags

Installation Overview

1. Attach each swivel clip to the bag’s D–rings or strap anchors.
2. Adjust the strap length between 45″ and 57.5″ to fit.
3. Position the shoulder pad for comfort on the carry point.
4. Verify clips are fully closed and secure before use.
5. Detach clips to remove and store the strap when not in use.

Occidental Leather 5068 Features

• Durable all-leather body with reinforced stitching
• Snap-closure flap keeps contents secure
• Fits Construction Master I–IV and most similar calculators
• Belt compatible: fits 1" to 3" wide belts
• Mount options: Belt-worn or Clip-on (varies by color)
• Available colors: OxyRed, OxyBlack
• Made in the USA

Occidental Leather 5068 Applications

• Protecting construction calculators on the jobsite
• Hands-free belt carry for quick calculator access
• Preventing drops, dirt, and damage during work

Occidental Leather 5068 Installation Overview

1. Choose belt-worn or clip-on attachment.
2. Thread onto a 1"–3" belt or attach via the clip.
3. Insert the calculator fully into the case.
4. Close the snap and verify secure retention.

Occidental Leather B5068 Key Features

• All-leather belt case with reinforced stitching for durability
• Secure snap closure to keep your calculator protected
• Fits belts up to 3 inches wide
• Compatible with Construction Master models I, II, III, IV and other brands
• Also available as Clip-On model B6568
• Made in USA

Occidental Leather B5068 Applications

• Jobsite protection and carry for construction calculators
• Belt-mounted storage for quick access while measuring and planning
• Compatible use with popular Construction Master calculator models

Occidental Leather B5068 Installation Overview

1. Slide the case onto a belt up to 3 inches wide.
2. Insert the calculator into the case.
3. Close the snap to secure the device.
4. Verify the case is seated firmly on the belt before use.

Occidental Leather 6568 Features

• All-leather construction with reinforced stitching for durability
• Secure snap closure keeps devices protected
• Clip-on attachment for quick belt or pocket mounting
• Fits Construction Master models I, II, III, IV and other brands
• Also available as a belt-worn model (5068)

Occidental Leather 6568 Applications

• Carry and protect construction calculators on the jobsite
• Quick access to calculator during layout and measurement tasks
• Hands-free storage while climbing ladders or moving materials

Occidental Leather 6568 Installation Overview

1. Insert calculator into the case.
2. Close the flap and snap to secure.
3. Slide the metal clip over your belt or waistband until fully seated.
4. Verify the case is firmly attached before working.

Occidental Leather B9019 Features

• Compact, straightforward utility pouch for added belt storage
• Single open compartment for flexible use
• Padded double-wall industrial nylon for lightweight durability
• Made in the USA

Occidental Leather B9019 Applications

• Extra storage on tool belts
• Light-duty tasks carrying essential fasteners or small tools
• Used as a third bag to expand capacity

Occidental Leather B9019 Installation Overview

1. Slide the pouch loop over your work belt.
2. Position on the preferred side for easy access.
3. Load with fasteners or small tools and confirm a secure fit.

Occidental Leather 5020 Features

• Dual-function design: integrated hammer loop plus pocket for a hand tool
• Space-saving footprint to free up room on your belt
• 12 oz English bridle leather for long-term durability
• Slides onto standard tool belts for quick setup
• Heavy-duty stitching and metal rivets for jobsite toughness
• Made in the USA

Occidental Leather 5020 Applications

• Carry a hammer and primary hand tool together on one holder
• Framing, trim, and general carpentry tool belts
• Remodeling and punch-list work where compact carry is key
• Workshop use and weekend DIY tasks
• Jobsite setups needing fast access without adding bulk

Occidental Leather 5020 Installation Overview

1. Thread the holder onto your tool belt at the preferred position.
2. Orient the pocket and loop for dominant-hand access.
3. Seat the hammer in the front loop and place a hand tool in the pocket.
4. Check that tools hang freely with no interference while walking or kneeling.
5. Reposition on the belt if needed for balance and comfort.

Occidental Leather 8551 Features

• 2" steel belt clip for rapid on/off at the waist
• Drawstring closure keeps fasteners and small tools secure
• Dual-layer construction: 1000D nylon sides / 1050D nylon bottom
• Small size: 5" diameter x 6" high
• Made in the USA
• Clips to most belts or waistbands up to 2" wide

Occidental Leather 8551 Applications

• Carry nails, screws, and small fasteners on the job
• Quick-access storage for bits, small hand tools, and hardware
• Trim work and finish tasks needing lightweight organization
• Framing and decking where fastener access is essential
• Service and repair jobs requiring compact tool storage

Occidental Leather 8551 Installation Overview

1. Attach the 2" steel clip to your belt or waistband.
2. Load fasteners or small tools into the pouch.
3. Cinch the drawstring to secure contents.
4. Position for comfortable access during work.
5. Release the clip for quick removal when finished.

Occidental Leather B8551 Key Features

• 2" steel clip for rapid belt or waistband attachment
• Drawstring closure keeps fasteners and parts contained
• Dual-layer construction: 1000D nylon sides with 1050D nylon base
• Compact Small size for light, efficient carry
• Made in the USA

Occidental Leather B8551 Applications

• Carry nails, screws, and small hardware on the job
• Quick clip-on storage for carpentry and framing tasks
• Handy parts pouch for electrical, drywall, or finish work
• Supplemental storage on tool belts or work pants

Occidental Leather B8551 Installation Overview

1. Attach the 2" steel clip to a belt or waistband (up to 2" wide).
2. Load fasteners or small tools into the pouch.
3. Pull the drawstring to secure contents.
4. Release the drawstring and unclip to remove when finished.

Occidental Leather 5237 Features

• Clip-on design allows installation without removing your belt
• High-mount position for reduced swing and better mobility
• Proprietary steel belt clip fits up to 2" wide belts
• Durable, heirloom-quality leather construction
• Made in USA
• Extra Large size tailored for 35’ FatMax tapes

Occidental Leather 5237 Applications

• Secure belt-mounted carry for 35’ FatMax tape measures
• Carpentry, framing, and general construction work
• Improving jobsite mobility by keeping tape accessible
• Reducing tape swing during movement
• Use with tool belts up to 2" wide

Occidental Leather 5237 Installation Overview

1. Slide the steel clip over your belt (fits up to 2" wide) at a preferred high-mount position.
2. Seat the holster firmly against the belt to ensure a secure grip.
3. Insert the 35’ FatMax tape into the holster opening.
4. Confirm the tape is retained and easily accessible.
5. Remove or reposition quickly as needed without taking off the belt.

Occidental Leather 5137 Key Features

• Belt-worn, high-mount design for improved mobility
• Sized for 35' FatMax tape measures
• Premium, durable leather construction
• Fits belts up to 3″ wide
• Handcrafted in the USA

Occidental Leather 5137 Applications

• Secure tape measure carry for framing & carpentry
• General construction measuring tasks
• Jobsite mobility where quick access is essential
• Tool belt organization for professional trades

Occidental Leather 5137 Installation Overview

1. Slide the holster onto a work belt up to 3″ wide.
2. Position high on the belt for comfortable reach.
3. Insert your 35' FatMax tape into the pocket.
4. Confirm secure fit before use.

Occidental Leather 9502 Features

• Double clip-on design adds fastener capacity and subdivides existing bags
• Leather clip-on patch ideal for phone, notebook, or small tools
• Clips securely to belts up to 2″ or to toolboxes
• Industrial nylon construction for lightweight durability
• Made in the USA

Occidental Leather 9502 Applications

• Add-on fastener storage for existing tool belts
• Organize small tools & hardware on the job
• Sub-divide main bags for better workflow
• Preload and clip to toolbox or truck for quick access
• Use on work belts up to 2″ wide

Occidental Leather 9502 Installation Overview

1. Position pouch clip on a work belt up to 2″ wide or on a toolbox edge.
2. Secure the clip fully and check for a tight hold.
3. Load fasteners or small tools into the main and outer bags.
4. Optionally use it to sub-divide items in your primary bags.
5. Remove and store when not in use.

Key Features

• Lower back support pad for enhanced comfort during long wear
• Fits under a third bag or hammer holder on most work belts
• High-density foam with polyethylene stiffener for stability
• Industrial nylon exterior for durability
• Made in USA

Applications

• Add lumbar support to existing tool belts
• Use beneath a fastener bag or hammer holder without bulk
• Improve comfort for prolonged standing or bending tasks
• General carpentry, framing, finish work, and jobsite use

Installation Overview

1. Remove or loosen adjacent bags/holders on your work belt.
2. Thread the Belt Buddy onto the belt and center it at the lower back.
3. Reattach the third bag or hammer holder over the pad as desired.
4. Adjust belt fit for comfort and support.

Occidental Leather 5046 Key Features

• Clip-on design installs without removing your belt
• Proprietary extra-long, wide steel clip resists accidental release
• High-mount position reduces swing and improves mobility
• Heirloom-quality leather withstands tough jobsite conditions
• Made in the USA

Occidental Leather 5046 Applications

• Securely carry a tape measure on tool belts up to 2″ wide
• Framing and carpentry measuring tasks
• General construction and remodeling
• Jobsite mobility with quick tape access

Occidental Leather 5046 Installation Overview

1. Position the clip over your belt (fits up to 2″ wide).
2. Slide the holster down until the clip locks onto the belt.
3. Insert the tape measure into the leather holster.
4. Confirm secure engagement and comfortable placement.

Key Features

• High-mount design keeps tape accessible and out of the way
• Fits belts up to 3 in. wide
• Premium, durable leather construction
• Made in the USA
• Size 5037 (Large) fits most 30’ tapes; accommodates FatMax without clip

Applications

• Securely carry a tape measure on a tool belt
• Framing, trim, and general carpentry tasks
• Jobsite measuring where quick access is essential

Installation Overview

1. Thread the holster onto a belt up to 3 in. wide.
2. Select the correct size; 5037 is for most 30’ tapes.
3. Insert the tape measure; remove the clip if using FatMax for best fit.
4. Position holster on belt for preferred high-mount access.

Occidental Leather 8505 Key Features

• Clip-on mount fastens to belt or pocket
• 4 pockets for utility knife, pencils, and 35’ tape
• Lightweight, jobsite-tough design
• Made in the USA

Occidental Leather 8505 Applications

• Keep tape, knife, and pencils within reach while working
• Add-on clip pouch for belts, pockets, or vests
• Organized storage for measuring and marking tasks

Occidental Leather 8505 Installation Overview

1. Attach the clip to your belt or pocket.
2. Load tools into the designated pockets.
3. Verify secure fit and adjust position for comfort.

Occidental Leather 5028 Features

• Multi-use pouch designed for snips; also fits various small tools
• Rigid leather build for a secure, low-swing carry
• Slides onto belts up to 3" wide for a stable fit
• Durable full-grain leather construction
• Handcrafted in the USA

Occidental Leather 5028 Applications

• Steel framing and metal stud work
• Carpentry and general contracting
• Daily belt carry for aviation snips and similar tools
• Low-swing hammer or tool carry alternative

Occidental Leather 5028 Installation Overview

1. Slide the holster onto a belt up to 3" wide.
2. Insert snips or a compatible tool fully into the pocket.
3. Check clearance and secure positioning before use.
4. Periodically clear debris and verify fit.

Key Features

• Long sleeve design reduces tool swing and keeps handles secure
• All-leather construction for durability
• Holds hammers, hammer tackers, and flat bars (up to 1 5/8” diameter)
• Fits work belts up to 3” wide
• Made in the USA

Applications

• Carry and secure hammers while walking or climbing
• Hold hammer tackers and flat bars without excessive swinging
• Ideal for framing, carpentry, and general construction

Installation Overview

1. Thread the holder onto a belt up to 3” wide.
2. Position the sleeve at your preferred carry location.
3. Insert the tool handle fully into the leather sleeve.
4. Verify secure fit and minimal swing during movement.

Occidental Leather 5032 Key Features

• All-leather construction built for tough jobsite use
• Tapered design securely holds bull pins or nail bars
• Slides onto belts up to 3" for comfortable, hands-free carry
• Handcrafted in the USA
• Compact size for minimal swing and quick access

Occidental Leather 5032 Applications

• Bull pin carry for ironworkers and steelworkers
• Nail bar storage on tool belts
• Jobsite belt accessory for organized tool access
• Daily use in construction and industrial settings

Occidental Leather 5032 Installation Overview

1. Slide the holster onto a belt up to 3" wide.
2. Position at preferred carry location for access.
3. Insert bull pin or nail bar into tapered pocket.
4. Check retention and adjust belt placement as needed.
5. Inspect stitching and rivets periodically for wear.