Occidental Leather
Occidental Leather 5518 No Slap Hammer Holder
$30.90
Unit price perOccidental Leather 5518 No Slap Hammer Holder Description
Secure and stabilize your hammer with the all-leather No Slap Hammer Holder. The long sleeve-style design keeps handles upright to minimize swing and prevent “knee-capping,” while fitting belts up to 3” wide. Built from heavy-duty leather and made in the USA.
Includes
- (1) Occidental Leather 5518 No Slap Hammer Holder
Key Features
- Long sleeve design reduces tool swing and keeps handles secure
- All-leather construction for durability
- Holds hammers, hammer tackers, and flat bars (up to 1 5/8” diameter)
- Fits work belts up to 3” wide
- Made in the USA
Applications
- Carry and secure hammers while walking or climbing
- Hold hammer tackers and flat bars without excessive swinging
- Ideal for framing, carpentry, and general construction
Installation Overview
- Thread the holder onto a belt up to 3” wide.
- Position the sleeve at your preferred carry location.
- Insert the tool handle fully into the leather sleeve.
- Verify secure fit and minimal swing during movement.
Specifications
| Material | Heavy-duty leather |
| Tool Capacity | Hammers, tackers, flat bars up to 1 5/8” diameter |
| Belt Compatibility | Up to 3” wide |
| Weight | 0.3 lb |
| Country of Origin | USA |
Occidental Leather 5518 No Slap Hammer Holder
Leather no-slap hammer holster, fits 3" belts
✓ Long sleeve design reduces swing and prevents knee-capping
✓ All-leather construction for durable, jobsite performance
✓ Tool capacity: holds hammers, hammer tackers & flat bars up to 1 5/8" diameter
✓ Belt fit: accepts belts up to 3" wide
✓ Made in USA
$30.90
Unit price per21 in stock
Pay with
Your transaction is protected with advanced security measures to keep your information confidential
Leather Gear Care
- Brush off jobsite grit daily; wipe with a damp rag when muddy.
- Shake out debris from inside as needed.
- For deeper grime, use mild soap and water (no bleach or harsh solvents) and allow to air dry.
- About once a year, clean with saddle soap or mild soap and warm water, then apply a small amount of non-oil-based leather conditioner.
- Store dry and out of direct sun to extend life.
* Avoid oil-based products; they can weaken stitching and shorten leather life.
* Wipe off mud, concrete, or drying compounds with a damp cloth before they dry.
- Long Sleeve Design — Minimizes swing and keeps tools upright
- Full Leather Construction — Durable, jobsite-proven build
- Versatile Capacity — Holds hammers, hammer tackers, and flat bars (to 1 5/8” Ø)
- Wide Belt Compatibility — Fits belts up to 3” wide
- Made in USA
- Material: Heavy-duty leather
- Tool Capacity: Up to 1 5/8” diameter
- Belt Fit: Up to 3” wide
- Weight: 0.3 lb
More About Occidental Leather 5518 No Slap Hammer Holder
Occidental Leather 5518 No Slap Hammer Holder Description
Secure and stabilize your hammer with the all-leather No Slap Hammer Holder. The long sleeve-style design keeps handles upright to minimize swing and prevent “knee-capping,” while fitting belts up to 3” wide. Built from heavy-duty leather and made in the USA.
Includes
- (1) Occidental Leather 5518 No Slap Hammer Holder
Key Features
- Long sleeve design reduces tool swing and keeps handles secure
- All-leather construction for durability
- Holds hammers, hammer tackers, and flat bars (up to 1 5/8” diameter)
- Fits work belts up to 3” wide
- Made in the USA
Applications
- Carry and secure hammers while walking or climbing
- Hold hammer tackers and flat bars without excessive swinging
- Ideal for framing, carpentry, and general construction
Installation Overview
- Thread the holder onto a belt up to 3” wide.
- Position the sleeve at your preferred carry location.
- Insert the tool handle fully into the leather sleeve.
- Verify secure fit and minimal swing during movement.
Specifications
| Material | Heavy-duty leather |
| Tool Capacity | Hammers, tackers, flat bars up to 1 5/8” diameter |
| Belt Compatibility | Up to 3” wide |
| Weight | 0.3 lb |
| Country of Origin | USA |
Sizing Guide
Important: Skip the Pants Size!
Forget your pants waist measurement – it won't give you the right fit. Here's the proper way to size your tool belt.
Measuring Your Belt Size:
The most accurate method is to measure a tool belt you already wear regularly. Here's how:
- Put on your typical work clothes (pants, regular belt, shirt, hoodie – whatever you normally wear on the job).
- Wear your current tool belt at your usual position and fasten it to your preferred comfort level. Take note of which hole you're using.
- Remove the belt and lay it flat on a surface. Measure from the buckle's end to the hole you were using. This measurement is your true belt size.
- Match your measurement to the sizing chart below.
Don't Have a Tool Belt Yet?
No problem – borrow one from a colleague for measuring, or use a cloth measuring tape or rope around your waist where you'd wear the belt (over your work clothes). Measure where it feels comfortable.
Sizing Tips:
- Between sizes? Go with the larger option for optimal comfort.
- These belts are engineered to fasten at the center hole, giving you 4 inches of adjustment in either direction (9 holes total spanning 8 inches).
- Always measure over your full work outfit – tool belts sit over everything you're wearing.
Sizing Chart:
- Small: 34" (86.5 cm)
- Medium: 37" (94 cm)
- Large: 41" (104.5 cm)
- X-Large: 45" (114.5 cm)
- XX-Large: 49" (124.5 cm)
- XXX-Large: 53" (135 cm)
Why Your Pants Size Doesn't Work:
- Pants use stretchy fabrics that conform to your body; our leather belts mold over time but aren't elastic.
- Clothing sizes are inconsistent – a size 36 in slim fit differs significantly from a relaxed 36.
- Tool belts go over your entire outfit, not just your waist.
- Most people need a belt 3-7 inches larger than their pants waist, depending on wear style and layering.
Measuring Instructions:
- You'll need a flexible tape measure and your tool belt.
- With your tool belt on, measure from the top of your toolbelt where the suspenders will attach in the back.
- Bring the tape measure diagonally up and over the opposite shoulder to the top of the belt where suspenders will attach in the front.
- Round that measurement up to the nearest whole number.
Sizing Chart:
- Small: ≤ 38" (96.5 cm)
- Standard: 38-48" (96.5 - 122 cm)
- Extension Kit: > 48" (122 cm)
The installation process involves riveting the hammer sleeve directly to your chosen pouch or rig:
- Position the Sleeve: Determine the optimal placement on your pouch or rig. The sleeve should be positioned where you want to carry your hammer typically behind or on the side of your main pouch for easy access.
- Mark Your Holes: Align the hammer sleeve with your pouch and mark where the rivet holes will go through both the sleeve and your pouch/rig.
- Install the Copper Rivets: Using the included copper rivets, secure the hammer sleeve to your pouch. The rivets provide a permanent, durable attachment that will withstand years of daily use.
- Check the Fit: Once installed, test your hammer's fit. It should slide in and out easily while remaining secure during movement.
Installation Tips:
- Take your time positioning the sleeve before making permanent holes - measure twice, drill once.
- The sleeve is designed to tuck your hammer behind your pouch, keeping it close to your body and out of the way.
- Make sure the hammer head will be easily accessible when you reach for it.
- Consider your dominant hand and work style when choosing placement.
- For detailed visual guidance, refer to the installation video provided with your kit or available on Occidental Leather's website.
What Are the Benefits?
- No More Leg Slapping: Keeps your hammer from swinging and hitting your legs
- Quick Access: Positions hammer at your fingertips for one-handed retrieval
- Compact Carry: Tucks hammer close to your body, ideal for working in tight spaces
- Protects Your Work: Prevents hammer from damaging freshly installed materials like cabinets, drywall, or trim
- High Mobility: Perfect for framing, roofing, finish carpentry, and other jobs requiring freedom of movement
How Long Will It Last?
Made from 8 oz leather and secured with copper rivets, the Occidental Hammer Sleeve is built to endure years of daily jobsite use when properly maintained.
Can I Remove It Later?
No - the copper rivet installation is permanent. Choose your placement carefully before installation. This permanent attachment ensures maximum durability and reliability on the job.
Do I Need Special Tools?
You'll need basic rivet-setting tools to install the copper rivets. If you're not familiar with setting rivets, consider having a leather worker or experienced colleague help with the installation, or watch the provided video tutorial first.
Top Sellers
Our Highest Quality Products
