Holiday Gift Guide 2021

Occidental Leather 5085 Key Features

• 17 pockets and holders for organized storage inside and out
• Divided interior for separated, easy-to-reach tool access
• Quick-release snap and strap for electrical tape
• Holster fits a 35 ft x 1 in tape measure
• Constructed from 8 oz top grain leather; Made in USA
• Tunnel loop fits up to a 3 in work belt

Occidental Leather 5085 Applications

• Organizing hand tools for jobsite or shop use
• Carrying screwdrivers, pliers, knives, chisels, markers, and strippers
• Holding torpedo level, hammer, and tape measure
• Attaching to belts up to 3 in for hands-free access

Occidental Leather 5085 Installation Overview

1. Thread a work belt (up to 3 in wide) through the tunnel loop.
2. Position the case at preferred location on your belt.
3. Load tools into divided pockets for balanced weight.
4. Secure tape to the strap and attach items to the quick-release snap as needed.
5. Verify pockets and snap are closed before use.

Occidental Leather 5526 Key Features

• Round-bottom leather construction adds volume and resists collapse
• Tool-specific storage: torpedo level slot, bit holders, pencil and chisel pockets
• Right-hand layout; worn on the right side
• Includes Oxy Tool Shield for safe carry of sharp tools
• Not available in a left-hand model

Occidental Leather 5526 Applications

• Carpentry and framing tool organization on a work belt
• Right-hand access to frequently used tools
• Jobsite fastener and small tool storage
• General construction and remodeling tasks

Occidental Leather 5526 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the right side for dominant-hand access.
3. Insert the Oxy Tool Shield into the designated pocket.
4. Load tools into dedicated holders and pockets.
5. Check balance and security before working.

Occidental Leather 5525 Key Features

• Round-bottom design increases internal volume and stability
• 10 pockets and holders optimized for fasteners and layout tools
• Tape pocket fits tapes up to 35 ft
• Includes Oxy Tool Shield to protect sharp tools, bags, and body
• Right-hand layout; worn on the left side
• Premium leather construction; Made in the USA

Occidental Leather 5525 Applications

• Fastener storage for framing and carpentry tasks
• Organizing layout tools like squares and bits
• Measuring and marking with quick tape access
• Daily jobsite carry on a work belt

Occidental Leather 5525 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the left side for right-handed use.
3. Insert the Oxy Tool Shield into the designated holder.
4. Load fasteners and tools into the appropriate pockets.
5. Confirm secure fit and balance before use.

Key Features

• 5 inch wide belt for added back support
• Padded wool liner for moisture wicking comfort
• 2 inch leather overbelt keeps bags from sliding
• Nickel plated steel buckles and built in suspender loops
• Edge stitched leather for durability
• Made in USA

Applications

• Comfortable support for heavy tool rigs
• Securing clip on tool bags and pouches
• Use with suspenders for balanced load carry
• General construction and carpentry work

Installation Overview

1. Measure your existing tool belt from buckle end to the used hole to confirm size.
2. Place the belt where you wear your rig over normal work clothing.
3. Buckle using the midpoint hole for best adjustment range.
4. Attach tool bags to the overbelt and secure through belt loops.
5. Clip suspenders to the attachment loops if used.

Occidental Leather 5135 XL Key Features

• Wide 5 in belt enhances back support
• Suspender attachment loops pre-installed
• Thick padded interior for comfort and moisture control
• Heavy duty buckles and belt loops minimize bag sliding
• Edge stitched leather construction
• Made in USA

Occidental Leather 5135 XL Applications

• Supporting tool bags for carpentry and construction
• Improving lower back support during long work days
• Use with suspenders for added load distribution
• Jobsite wear requiring durable leather work belts

Occidental Leather 5135 XL Installation Overview

1. Measure an existing tool belt from buckle end to the most used hole.
2. Select the size closest to that mid-range measurement.
3. Put the belt on over normal work clothes and adjust to comfort.
4. Attach suspenders to the built-in loops if desired.
5. Secure tool bags to the overbelt and verify they do not slide.

Occidental Leather B5135 M Key Features

• Wide 5 in. belt for added lower back support
• Suspender attachment loops
• Thick padded interior for comfort and moisture wicking
• 2 in. leather overbelt plus heavy duty buckles and belt loops minimize bag sliding
• Handcrafted in the USA from premium Latigo leather

Occidental Leather B5135 M Applications

• Support and stabilize tool bags and pouches on the job
• Use with suspenders for added load distribution
• Daily wear for construction, carpentry, electrical, and trades
• Upgrading comfort on existing Occidental Leather systems

Occidental Leather B5135 M Installation Overview

1. Measure an existing work belt or measure from buckle to the hole you use to confirm size.
2. Thread tool bags onto the 2 in. overbelt as desired.
3. Position the belt at working height and buckle to a comfortable hole.
4. Attach suspenders to the loops if used and adjust for balance.
5. Reposition bags so weight is centered and movement is minimized.

Key Features

• Wide 5 in belt for enhanced back support
• Suspender attachment loops
• Thick padded interior for comfort and moisture wicking
• Heavy-duty buckles and belt loops minimize bag sliding
• 2 in all-leather overbelt; edge-stitched for strength
• Made in the USA

Applications

• Supporting tool bags and pouches on the jobsite
• Use with suspenders via integrated attachment loops
• Comfortable heavy-duty belt for framing, finish, or general carpentry

Installation Overview

1. Put the belt on over typical work clothing where you will wear it.
2. Measure from the buckle to the hole you use; that measurement is your belt size.
3. Select size XL (approx. 45 in belt size) and adjust using the 9-hole range.
4. Attach tool bags to the overbelt and secure through the belt loops.
5. Clip suspenders to the attachment loops if desired and check fit.

Occidental Leather 5135 LG Key Features

• 5 in wide belt for back support
• Suspender attachment loops pre-installed
• Thick padded interior for comfort and moisture control
• Heavy-duty buckles and belt loops minimize bag movement
• Edge-stitched leather construction
• Made in USA

Occidental Leather 5135 LG Applications

• Daily wear with Occidental tool bags and systems
• Added back support for heavy tool loads
• Suspender-compatible setups for long shifts
• Carpentry, framing, electrical, and general construction

Occidental Leather 5135 LG Installation Overview

1. Measure an existing tool belt from buckle tip to your used hole to confirm size.
2. Select Large (41 in mid range) and adjust using the 9-hole range.
3. Attach tool bags to the overbelt and secure using belt loops.
4. Connect suspenders to the attachment loops as needed.
5. Check fit and tighten buckles to prevent sliding.

Occidental Leather 5135 XXL Key Features

• 5 in. wide belt for enhanced back support
• Built-in suspender attachment loops
• Thick padded wool liner for comfort and moisture control
• Heavy duty buckles and belt loops minimize bag sliding
• Edge stitched leather for added strength

Occidental Leather 5135 XXL Applications

• Securely carry tool bags and pouches
• Provide back support during long workdays
• Use with suspenders for balanced load distribution
• Carpentry, framing, and general construction tasks
• Comfortable wear over layered work clothing

Occidental Leather 5135 XXL Installation Overview

1. Measure your current tool belt from buckle end to the hole you use.
2. Select size based on midpoint measurement; size up if between.
3. Wear over typical work clothing and fasten at the midpoint hole.
4. Attach tool bags to the overbelt loops; tighten to prevent sliding.
5. Clip suspenders to built-in loops for added support if needed.

Occidental Leather B5135 LG Key Features

• 5 in wide belt provides added back support
• Suspender attachment loops for optional load distribution
• Thick padded, moisture wicking interior for comfort
• Heavy duty buckles and belt loops minimize bag sliding
• 2 in all leather overbelt keeps pouches stable
• Nickel plated steel hardware; edge stitched for strength
• Handcrafted in the USA

Occidental Leather B5135 LG Applications

• Carrying and stabilizing tool pouches on the jobsite
• Reducing lower back strain during all day wear
• Use with suspenders for added weight distribution
• General construction, carpentry, electrical, and finish work

Occidental Leather B5135 LG Installation Overview

1. Select correct size; position belt around waist over work pants.
2. Thread tool bags onto the overbelt and place in desired positions.
3. Buckle the belt and tighten to a comfortable, secure fit.
4. Attach suspenders to the loops if using for extra support.
5. Recheck fit and adjust pouch spacing as needed.

Occidental Leather B5135 SM Key Features

• 5 in wide belt for enhanced back support
• Padded wool liner for moisture-wicking comfort
• 2 in all-leather overbelt helps prevent bag sliding
• Nickel-plated steel buckles and hardware
• Integrated suspender attachment loops
• Edge-stitched Latigo leather for strength and clean finish
• Handcrafted in the USA

Occidental Leather B5135 SM Applications

• Securely carry and stabilize tool bags and pouches
• Back support for all-day wear on construction sites
• Use with suspenders for balanced load distribution
• General carpentry, framing, remodeling, and trades work

Occidental Leather B5135 SM Installation Overview

1. Measure your existing tool belt from buckle end to the hole you use to confirm size.
2. Position the Stronghold belt where you wear your rig and buckle to the midpoint hole.
3. Slide tool bags onto the 2 in overbelt and secure in desired positions.
4. Attach compatible suspenders to the built-in loops if needed.
5. Fine-tune fit for comfort and even weight distribution.

Occidental Leather 5135 M Key Features

• Wide 5 in belt for enhanced back support
• Built in suspender attachment loops
• Thick padded wool liner for comfort and moisture control
• Heavy duty buckles and belt loops reduce bag sliding
• Edge stitched leather for added strength
• Made in USA

Occidental Leather 5135 M Applications

• Securely carry tool bags and pouches on the job
• Provide back support during long workdays
• Use with suspenders for balanced load distribution
• Suitable for carpentry, framing, and general trades
• Comfortable wear in warm or active conditions

Occidental Leather 5135 M Installation Overview

1. Measure an existing tool belt from buckle end to the most used hole to find belt size.
2. Select Medium if your measurement is near 37 in midpoint.
3. Wear over standard work clothing and tighten using the preferred hole.
4. Attach tool bags to the overbelt and loops; add suspenders if needed.
5. Confirm comfortable fit and adjust within the available holes.

Occidental Leather B5135 XXL Key Features

• 5 inch wide belt for enhanced back support
• Padded wool liner for comfort and moisture control
• 2 inch all leather overbelt keeps tool bags in place
• Nickel plated steel buckles and hardware
• Built in suspender attachment loops
• Edge stitched for durability and clean appearance
• Made in the USA

Occidental Leather B5135 XXL Applications

• Daily tool carry with improved back support
• Securing Occidental tool bags with minimal sliding
• Use with suspenders for balanced load distribution
• Carpentry, framing, and general construction work
• Comfort focused belt upgrade for heavy rigs

Occidental Leather B5135 XXL Installation Overview

1. Put the belt on over typical work clothing and note the hole used.
2. Remove and measure from the end of the buckle to the used hole.
3. Select the size closest to that measurement; this model is XX Large.
4. Attach tool bags to the overbelt loops; tighten to minimize sliding.
5. Connect compatible suspenders to the attachment loops if desired.

Occidental Leather B5055 Features

• Even load distribution to relieve hip and lower back strain
• Padded, contoured yoke with sweat-wicking lining
• Secure fit keeps straps from wandering off shoulders
• Tool-friendly chest pockets on both sides
• Heavy-duty center D ring for hanging your rig
• Leather loop attachment system fits up to a 3 in. belt
• Made in USA

Occidental Leather B5055 Applications

• Support and stabilize heavy tool belts during daily use
• Reduce lower back and hip fatigue on framing and carpentry jobs
• Keep rigs balanced when carrying bulky tools and fasteners
• Quickly hang up complete belt systems between tasks

Occidental Leather B5055 Installation Overview

1. Attach leather loops to your tool belt (up to 3 in. width).
2. Connect front clips and set the chest strap to a comfortable tension.
3. Adjust strap lengths for even weight distribution.
4. Check shoulder yoke alignment and secure fit before use.
5. Use the center D ring to hang the rig when removing.

Occidental Leather 5055 Features

• Even load distribution for reduced hip and back fatigue
• Padded, contoured yoke lined with Dri-Lex for moisture wicking
• Chest pockets for pencils and clip-on items on both sides
• Easy on-off with adjustable chest strap
• Heavy-duty D-ring for hanging the rig
• One size fits most
• Made in USA

Occidental Leather 5055 Applications

• Support and stabilize loaded tool belts during long shifts
• Improve comfort and reduce strain for framing and carpentry work
• Keep suspenders and straps securely positioned while moving
• Hang up belt rig between tasks using center D-ring

Occidental Leather 5055 Installation Overview

1. Attach the leather loop connectors to your work belt (up to 3 in).
2. Clip the suspender straps to the belt loops.
3. Adjust the chest strap for a secure, comfortable fit.
4. Set strap lengths to distribute weight evenly across shoulders.
5. Confirm all connections are secure; D-ring is for hanging only.

Occidental Leather 5570 Features

• Full grain leather construction for durability
• Dedicated holders for circle cutter, metal snips, saw, knife, Surform, Oxy tool shield, C-clamps, pencils, and hammer
• Designed for right hand use
• Optimized for drywall professionals
• Keeps all essential tools within easy reach
• Made in the USA

Occidental Leather B5612 Features

• Light-weight, classic black all leather construction
• External leather hammer holder and double outer bags
• Internal pockets for level, chisel, drill bits, knife, pencils, and lumber crayon
• Reinforced back wall at stress points for durability
• Right-side wear layout; left-hand version available as B5612LH
• Made in USA

Occidental Leather B5612 Applications

• Organizing hand tools for carpentry and framing
• Quick-access storage for chisels, knives, pencils, and bits
• Carrying levels and small measuring tools
• General construction and remodel tool carry

Occidental Leather B5612 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the right side for right-hand access.
3. Load tools into main and outer pockets; place sharp tools in the Oxy Tool Shield.
4. Adjust placement for comfort and balanced weight.

Occidental Leather B5611 Features

• All leather construction with classic black finish
• Integrated Oxy Tool Shield for sharp tools
• Upper bag with sleeve pockets and drill bit holsters
• Side by side 35 ft tape holster and angle square holster
• Reinforced back wall at stress points
• Pockets & tool holders: 10
• Available left-hand version: B5611LH

Occidental Leather B5611 Applications

• Fastener and small tool organization for framing and carpentry
• Quick access to tape, angle square, and drill bits
• Left-side wear for tools commonly accessed with the left hand

Occidental Leather 5062LH Key Features

• Left-handed layout worn on the right side
• Same features as 5060LH plus an additional outer pouch
• Holders for blade square, angle square, driver bits, and cat's paw
• 10 total pockets and tool holders
• Full-grain leather construction for durability
• Made in the USA

Occidental Leather 5062LH Applications

• Framing and rough carpentry fastener carry
• General carpentry tool and hardware organization
• Layout tasks requiring blade and angle squares
• Daily jobsite use where quick access to bits and small tools is needed

Occidental Leather 5062LH Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the right side of the body for left-handed use.
3. Load fasteners and tools into the four stacked compartments.
4. Use dedicated holders for squares, bits, and cat's paw.
5. Adjust placement for comfort and balanced carry.

Occidental Leather 5062 Features

• 4 pouch layout for compact, expanded capacity
• 10 pockets and tool holders for fasteners and layout gear
• Tool-specific slots for blade square, angle square, driver bits, and cat's paw
• Full-grain leather construction for long-term durability
• Worn on the non-dominant side; available as left-hand 5062LH
• Made in the USA

Occidental Leather 5062 Applications

• Framing and general carpentry tool and fastener carry
• Organizing layout tools like blade and angle squares
• Quick access to driver bits, nail sets, and cat's paw
• Left-side fastener storage for right-handed users

Occidental Leather 5062 Installation Overview

1. Slide the pouch onto a 3 in belt or compatible work belt.
2. Position on the left side for right-handed use or select 5062LH for left-handed layout.
3. Load fasteners and tools into the four stacked compartments.
4. Place blade square and angle square in designated holders; store bits and cat's paw in slots.
5. Confirm secure fit and balanced carry before use.

Occidental Leather 8581 Key Features

• FatLip leather mouth keeps the bag formed, open, and protected from abrasion
• Full leather boot for long-term durability
• Patented 2-in-1 outer bag with built-in angle square holster
• Dedicated sleeves and pouches for tri-square, cat's paw, nail sets, and driver bits
• Accepts belts up to 3 in wide
• Made in the USA

Occidental Leather 8581 Applications

• Carrying nails, screws, and common fasteners
• Organization for angle square, tri-square, and layout tools
• Holstering cat's paw and driver bits for framing and drywall tasks
• General construction use on the non-dominant side

Occidental Leather 8581 Installation Overview

1. Slide the bag onto a work belt up to 3 in wide.
2. Wear on the left side for right-handed setups.
3. Load fasteners and tools into main and outer compartments.
4. Seat the angle square in the built-in holster and secure small bits in dedicated pouches.
5. Verify comfortable position and accessibility before work.

Occidental Leather B5018DBLH Features

• 11 pockets and tool holders for common carpentry tools
• Main bag 9 x 8; outer bags 5 x 5.5 for organized access
• Integrated tape holster fits tapes up to 35 ft
• Premium black leather construction; left hand model
• Made in the USA

Occidental Leather B5018DBLH Applications

• Carry and organize chisels, knives, pencils and markers
• Secure holster for 35 ft tape measures
• Hold torpedo level and hammer for framing and finish work
• Left-side wear for left-hand tool access

Occidental Leather B5018DBLH Installation Overview

1. Slide the bag onto your work belt.
2. Position on the left side for left-hand access.
3. Load tools into designated pockets and holders.
4. Place tape measure in the built-in holster.
5. Verify balance and adjust belt for comfort.

Occidental Leather 5060LH Key Features

• Popular left handed leather fastener bag for pros
• Optimized for framing and general carpentry tasks
• Dedicated holders for 1 in blade square, angle square, cat paw, driver bits and more
• Left handed layout is worn on the right side for right hand access
• Durable leather construction with multiple pockets and tool holders

Occidental Leather 5060LH Applications

• Framing workflows needing fast access to nails and tools
• General carpentry organization on the jobsite
• Carrying blade and angle squares securely
• Right side wear for left handed builders

Occidental Leather 5060LH Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the right side for left handed use.
3. Load fasteners and tools into main and outer pockets.
4. Secure squares and driver bits in designated holders.
5. Adjust belt fit and check balance before work.

Occidental Leather 5564 Key Features

• All leather main bag with divided nylon double outer pouch
• Six black leather tool holders; four pouches total
• Optimized for wire nuts, couplers, and small fasteners
• Left side wear for fast access with the left hand
• Full grain leather and industrial nylon construction

Occidental Leather 5564 Applications

• Organizing and carrying fasteners and small parts
• Keeping layout and marking tools at hand
• Electrical and mechanical fittings storage
• Daily jobsite use with hybrid leather and nylon durability

Occidental Leather 5564 Installation Overview

1. Slide the belt loop over your work belt.
2. Position on the left side for non dominant hand access.
3. Distribute tools and fasteners among the divided pouches.
4. Secure frequently used layout tools in the leather holders.