Nylon Belts and Bags

Key Features

• Hand-specific tool holders for efficient workflow
• Padded two-ply bags maintain shape when empty or loaded
• Industrial nylon exterior with leather holders and reinforced corners
• FatLip leather mouth keeps bags open and resists wear
• Full leather boot for rugged longevity
• 3" HD ranger belt with center 2?in?1 tool & hammer holder
• Pockets & tool holders: 25
• Made in the USA

Applications

• Framing and production carpentry
• General construction and remodeling
• Jobsite tool and fastener organization
• Left- or right-hand optimized setups for daily use

Installation Overview

1. Measure an existing tool belt from buckle end to your most-used hole to determine size.
2. Select the belt size closest to that midpoint measurement.
3. Position tool bag on dominant hand side and fastener bag opposite.
4. Secure the belt at the midpoint hole; adjust for comfort and balance.
5. Load tools and fasteners by task to optimize workflow.

Occidental Leather 8581 Features

• FatLip™ leather mouth keeps the bag formed, open, and protected
• Full leather boot for long-term durability
• Patented 2-in-1 outer bag with built-in angle square holster
• Tri-square sleeve, cat’s paw loop, and external nail set/driver bit pouches
• 10 pockets & tool holders for efficient organization
• Designed to be worn on the non-dominant side for fastener access
• Made in the USA

Occidental Leather 8581 Applications

• Framing: Keep nails, angle square, and layout tools at hand
• Drywall installation: Store fasteners and driver bits for quick access
• General construction: Organize common hand tools and fasteners
• Remodeling: Versatile pouch setup for mixed trades

Occidental Leather 8581 Installation Overview

1. Thread the bag onto a compatible 3″ work belt.
2. Position on the non-dominant side for fastener access.
3. Load tools and fasteners into main, outer, and upper pockets.
4. Seat the angle square in the integrated holster; place tri-square and cat’s paw in their sleeves.
5. Verify comfortable reach and balance before use.

Key Features

• Hand-specific tool holder layout for efficient workflow
• Padded two-ply bags maintain shape
• Abrasion-resistant industrial nylon with OxyRed leather reinforcements
• NoSpill leather tool holders for secure access
• Made in the USA

Applications

• Framing and general carpentry
• Jobsite tool and fastener organization
• Rough construction and remodeling
• Left- or right-handed setups for professional builders

Installation Overview

1. Measure your current tool belt from buckle end to the hole you use most.
2. Match that measurement to the size chart midpoint (SM–XXXL).
3. Assemble belt, tool bag, fastener bag, and hammer holder per your handedness.
4. Adjust to the midpoint hole for best fit, with about 4" of adjustment each way.
5. Load tools and fasteners; verify balance and accessibility.

Key Features

• 10" deep main pouch for high capacity
• FatLip leather-reinforced mouth stays open and resists wear
• Full leather boot adds structure and durability
• 13 pockets & tool holders for organized access
• Right-hand layout; worn on the right side
• Made in the USA

Applications

• Daily carry of hand tools such as hammer, knife, pencils, and chisels
• Carpentry/framing setups on the dominant-hand side
• General construction and remodeling tool organization

Key Features

• Round-bottom, two-ply foam core bags hold shape empty or loaded
• Hand-specific tool holder layout optimizes working rhythm
• Function-engineered for trim, finish, and light framing tasks
• Padded nylon 3" belt with 12-oz belting leather tongue & steel roller buckle
• Includes Oxy Tool Shield for sharp tool protection
• Includes 2-in-1 Tool & Hammer Holder
• Available in right- or left-hand setups

Applications

• Trim and finish carpentry
• Light framing
• Cabinetry and interior installs
• Detail work in tight spaces

Installation Overview

1. Measure your current tool belt from buckle end to the commonly used hole to select size (or add 4" to pant waist as an estimate).
2. Wear the set over typical work clothing and buckle at the midpoint hole.
3. Place tool bag on dominant-hand side; fastener bag on the opposite side (swap for left-handed use).
4. Attach the Tool & Hammer Holder and Oxy Tool Shields as preferred.
5. Adjust belt fit and bag spacing for comfort and balance.

Occidental Leather 8018DB Features

• Popular OxyLights 3-pouch layout for everyday tools
• OxyRed leather reinforcement at stress points
• Heavy-duty hammer loop and tape measure holster (up to 35')
• Interior holders for knife, chisel, pencil, lumber crayon, and level
• Designed for right-side wear for right-handed users
• Lightweight nylon/leather hybrid construction; Made in USA

Occidental Leather 8018DB Applications

• Carpentry and framing tool carry
• Finish and trim work organization
• General construction and handyman tool storage
• Right-hand dominant setups needing quick access

Occidental Leather 8018DB Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the right side for dominant-hand access.
3. Load tools into dedicated holders and pouches.
4. Confirm balance and adjust placement for comfort.

Occidental Leather 8062 Key Features

• Same features as the 8060 with an added outer pouch
• 10 pockets & tool holders with dedicated storage for squares, driver bits, and cat’s paw
• Streamlined layout for compact carry
• Optimized for left-side wear (fasteners accessed with left hand)
• OxyLights nylon construction with leather reinforcements
• Made in USA

Occidental Leather 8062 Applications

• Framing tasks needing organized fastener access
• General carpentry where compact storage is preferred
• Left-side wear for non-dominant hand tool retrieval
• Jobsite organization for squares, bits, nail sets, and small tools

Occidental Leather 8062 Installation Overview

1. Slide the bag onto a compatible work belt.
2. Position on the left side for non-dominant hand access.
3. Load tools and fasteners into the designated pockets.
4. Confirm the bag is seated securely on the belt.
5. Adjust placement for comfortable reach and balance.

Occidental Leather 8585XL Features

• Hand-specific tool holders for efficient workflow
• Padded two-ply bags keep their shape when empty or loaded
• Extremely abrasion-resistant industrial nylon with leather reinforcements
• FatLip leather mouth stays open & protects against wear
• Full leather boot for rugged durability
• 3″ HD Ranger Belt for comfort and stability
• Available left-handed as 8585LH
• Made in the USA

Occidental Leather 8585XL Applications

• Framing and production carpentry
• General construction and remodeling
• Organized storage of tools and fasteners on site

Occidental Leather 8585XL Installation Overview

1. Measure an existing tool belt from buckle end to your most-used hole to find size.
2. Select Extra Large if the midpoint is about 45″ (approx. pant waist 40″–44″).
3. Place the tool bag on your dominant side and the fastener bag on the opposite side.
4. Buckle and adjust the 3″ Ranger Belt over typical work clothing for a secure fit.

Occidental Leather 9520 Features

• Compact 2-in-1 outer bag adds fastener capacity without bulk
• Reinforced nylon construction with round-bottom bags that hold shape
• Built-in speed square slot for quick access
• Designed for left-side wear to access fasteners with the left hand
• Includes Oxy Tool Shield for safe storage of sharp tools

Occidental Leather 9520 Applications

• Trim carpentry: keep small fasteners and layout tools at hand
• Framing: carry nails, bits, and a speed square efficiently
• Finish work: organized storage for detail tools and hardware
• General carpentry: left-side fastener access for balanced setups

Occidental Leather 9520 Installation Overview

1. Slide the bag onto your work belt at the left side (right-handed setups) or right side (left-handed setups).
2. Seat the pouch so the round-bottom pockets face outward for easy access.
3. Load fasteners and organize tools in the main, outer, and small holders.
4. Insert the speed square into the dedicated slot as preferred (inside or outside).
5. Place sharp tools in the Oxy Tool Shield and verify comfortable reach.

Key Features

• 10 in. deep main bag for high-capacity storage
• Leather FatLip mouth keeps the bag formed, open, and protected against abrasion
• Full leather boot reinforces the base for rugged jobsite durability
• Patented 2-in-1 outer bag with built-in angle square holster
• Dedicated sleeves/loops for tri-square, cat’s paw, nail sets or driver bits
• Pockets and tool holders: 10
• Made in the USA

Applications

• Organizing and carrying nails, screws, and small fasteners
• Quick access to angle square, driver bits, and layout tools
• Framing, drywall, and general construction tasks

Occidental Leather 8060 Key Features

• Lightweight OxyLights nylon construction for daily comfort
• 3-pouch layout: main, outer, and upper bags for organized access
• Tool-specific holders for blade square, angle square, cat’s paw, and driver bits
• Designed as a left-side fastener bag for framing and general carpentry
• Reinforced with leather at stress points for durability
• Made in the USA

Occidental Leather 8060 Applications

• Framing: Keep nails, layout tools, and bits organized
• General carpentry: Quick access to fasteners and small tools
• Jobsite setup: Left-hand fastener storage for balanced belt systems

Occidental Leather 8060 Installation Overview

1. Select handedness and position this fastener bag on the left side for right-handed setups.
2. Slide the bag onto a compatible work belt and secure in preferred position.
3. Load fasteners and layout tools into dedicated pockets/holders.
4. Verify balance and accessibility; adjust pouch position as needed.

Occidental Leather 8086 OxyLights Ultra Framer Features

• Designed with hand-specific tool holders
• Padded two-ply bags maintain structure
• Extremely abrasion-resistant industrial nylon
• Leather tool holders & corner reinforcement (NoSpill design)
• 7-pouch compact system with patented 2-in-1 outer pouch
• Available in left- or right-hand configurations (8086LH for lefties)
• Made in USA

Occidental Leather 8086 OxyLights Ultra Framer Applications

• Framing – carry nails, layout tools, and a hammer within reach
• Carpentry – organize hand tools, fasteners, and measuring gear
• Remodeling – lightweight setup for all-day wear
• Jobsite tool organization – keep essentials accessible and secure

Occidental Leather 8086 OxyLights Ultra Framer Installation Overview

1. Measure your current tool belt from buckle end to the hole you use.
2. Match that measurement to the size chart midpoint (SM–XXXL).
3. If no belt to measure, add 4″ to your pant waist for an approximate mid range.
4. Select left- or right-hand configuration as preferred.
5. Load tools and adjust belt to the midpoint hole for optimal fit.

Key Features

• Compact, round-bottom design ideal for trim & finish tasks
• Two-ply foam-core main & outer bags hold shape loaded or empty
• Clip-on leather tab for tape or accessory pouches
• Steel hammer holder for rugged durability
• Right-hand layout; left-hand model available as 9521LH
• Includes 2003 Oxy Tool Shield for sharp tool protection
• 12 pockets & tool holders for efficient organization
• Made in the USA

Applications

• Trim carpentry & cabinetry installation
• Light framing and punch-list tasks
• Finish work tool organization on the right-hand side
• Safe storage of chisels, knives & sharp tools using Oxy Tool Shield
• Everyday carry for pencils, utility knife, driver bits & nail sets

Installation Overview

1. Slide the bag onto a compatible work belt.
2. Wear on the right side for right-handed use; choose 9521LH for left-handed.
3. Attach the clip-on leather tab or accessory pouches as needed.
4. Place the 2003 Oxy Tool Shield in the inner pocket for sharp tool protection.
5. Load tools into pockets & holders and confirm secure fit.

Occidental Leather 5564 Key Features

• Hybrid build: leather main bag with dual-compartment industrial nylon outer pouch
• Four total pouches for fasteners and small parts
• Six black leather tool holders for bits, cat’s paw, and layout tools
• Left-side wear for fastener access with the non-dominant hand
• Made in the USA

Occidental Leather 5564 Applications

• Electrical work: organize wire nuts, couplers, and connectors
• General carpentry: keep layout tools and small fasteners accessible
• Remodeling and finish tasks: carry driver bits and small fittings
• Jobsite service work: compact storage for frequently used parts

Occidental Leather 5564 Installation Overview

1. Thread onto a compatible work belt.
2. Position on the left side for fastener access with the non-dominant hand.
3. Load fasteners and tools into the main and divided outer pouches.
4. Secure and adjust for comfortable reach and balance.

Occidental Leather B8064 Key Features

• 4-bag layout: main, outer, upper, and patented 2-in-1 outer pouch
• Integrated angle square holster between main and outer bags
• Dedicated holders for tri-square, cat’s paw, driver bits, and nail sets
• Right-handed layout — fastener bag is worn on the left side
• Industrial nylon with leather reinforcements for lightweight durability
• Pockets & tool holders: 10
• Made in USA

Occidental Leather B8064 Applications

• Framing and general carpentry tool and fastener organization
• Layout work requiring quick access to angle square and measuring tools
• Daily carry of nails, screws, and small hand tools on the jobsite

Occidental Leather B8064 Installation Overview

1. Thread onto a compatible work belt.
2. Position on the left side for right-handed setups.
3. Load fasteners and tools into the main, outer, and upper pouches.
4. Stow angle square in the integrated holster; place small bits in dedicated sleeves.
5. Adjust placement for comfort and balance during use.

Occidental Leather 8080DB Features

• Hand-specific tool holder layout improves workflow
• Padded two?ply nylon pouches maintain structure loaded or empty
• Industrial nylon body resists abrasion for long service life
• Leather tool holders and corner reinforcement for durability
• Includes heavy-duty hammer holder
• Made in the USA

Occidental Leather 8080DB Applications

• Framing and general carpentry
• Remodeling and residential construction
• Jobsite tool and fastener organization
• Right- or left-handed belt setups

Occidental Leather 8080DB Installation Overview

1. Measure your current tool belt from buckle end to the commonly used hole to determine midpoint size (or add 4" to pant waist for an estimate).
2. Select the corresponding belt size (Small–XXXL) and fit to the midpoint hole.
3. Slide the tool and fastener bags onto the belt and position for hand preference.
4. Attach the hammer holder at the rear or preferred location.
5. Tighten the belt and make final adjustments for comfort and access.